74HC2G66DC-Q100H
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-VFSOP (0.091, 2.30mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Series | Automotive, AEC-Q100 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Resistance | 70Ohm |
| Max Power Dissipation | 300mW |
| Base Part Number | 74HC2G66 |
| Pin Count | 8 |
| Operating Supply Voltage | 5V |
| Number of Circuits | 2 |
| Max Supply Voltage | 10V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 40μA |
| Max Supply Current | 20μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 16 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 23 ns |
| -3db Bandwidth | 200MHz |
| On-State Resistance (Max) | 70Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Current - Leakage (IS(off)) (Max) | 1μA |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 20ns, 27ns |
| Channel-to-Channel Matching (ΔRon) | 3 Ω |
| Crosstalk | -60dB @ 1MHz |
| Voltage - Supply, Single (V+) | 2V~10V |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
74HC2G66DC-Q100H Overview
As the electronic part is packed in 8-VFSOP (0.091, 2.30mm Width), international shipping is convenient. In order to provide high reliability, an advanced packaging method Tape & Reel (TR) is used. Surface Mount is where this multiplexer is located. Multiplexers and demultiplexers have a ratio of 1:1. An extended operating temperature of -40°C~125°C TA degrees Celsius. As part of its design, the 8 series is equipped with this electronic component. A SPST - NO switching circuit is used for these analog switches. The circuits in this analogue multiplexer number 2. 74HC2G66 can be used to search for analog multiplexer variants. As far as internal resistance is concerned, it has 70Ohm. To find out what the 8 pins do, please refer to the datasheets. In a normalsituation, users should not supply the switches with voltage higher than 10V. The digital multiplexer has a low cost Single supply. It is recommended to use 2V as the lowest voltage for the electrical part. This multiplexer would work with 40μA current. Using only a single voltage supply, this analog switch requires 2V~10V voltage. If you put voltage higher than 20μA on the digital multiplexer, damage may occur. There is a voltage range of 5V operating voltages for the electrical part. This is one of the Automotive, AEC-Q100 series.
74HC2G66DC-Q100H Features
Switch Circuit: SPST - NO
40μA Supply Current
-3db Bandwidth: 200MHz
74HC2G66DC-Q100H Applications
There are a lot of Nexperia USA Inc. 74HC2G66DC-Q100H Analog Switches & Multiplexers ICs applications.
- Battery Powered Systems
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Channelized and Unchannelized DS3 applications
- Sample-and-hold systems
- Data Acquisition Systems
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Audio/video switches
- Intelligent PBX
- Battery Powered Instruments
- Private Branch Exchange (PBX)
