74HC2G66GD,125
| Parameters | |
|---|---|
| Terminal Pitch | 0.5mm |
| Base Part Number | 74HC2G66 |
| Output | SEPARATE OUTPUT |
| Pin Count | 8 |
| Operating Supply Voltage | 5V |
| Max Supply Voltage | 10V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 40μA |
| Nominal Supply Current | 30mA |
| Power Dissipation | 300mW |
| Max Supply Current | 30mA |
| Throw Configuration | SPST |
| Turn On Delay Time | 150 ns |
| Number of Inputs | 2 |
| Supply Type | Single |
| Turn-Off Delay Time | 175 ns |
| -3db Bandwidth | 200MHz |
| On-State Resistance (Max) | 70Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Current - Leakage (IS(off)) (Max) | 1μA |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 20ns, 27ns |
| Channel-to-Channel Matching (ΔRon) | 3 Ω |
| Crosstalk | -60dB @ 1MHz |
| Switching | MAKE-BEFORE-BREAK |
| Voltage - Supply, Single (V+) | 2V~10V |
| Normal Position | NO |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-XFDFN |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2013 |
| JESD-609 Code | e3 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Resistance | 70Ohm |
| Terminal Finish | MATTE TIN |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 300mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Number of Functions | 2 |
74HC2G66GD,125 Overview
The electronic component is convenient to ship overseas because it is packed in a 8-XFDFN. This high-reliability packaging method uses advanced packaging methods Tape & Reel (TR). Multiplexers like this are mounted in the Surface Mount position. 1:1 is the number of circuits in the multiplexer and demultiplexer. An extended operating temperature of -40°C~125°C TA degrees Celsius. In total, there are 8 terminations. As part of the design of the 8 series, this electronic part has been incorporated into the system. Based on SPST - NO switching circuits, these analog multiplexers work. Try searching with 74HC2G66 to find analog multiplexer variants. An switch multiplexer with 70Ohm internal resistance has a value of 70Ohm. The functions of 8 pins can be found in the datasheets. Theswitch device is a typical Multiplexer or Switches. In a normalsituation, users should not supply the switches with voltage higher than 10V. A analog switch ic that has a cost-effective Single supply type. It is recommended that the electrical component receives a voltage of 2V. In order to operate this switch device, it would need a current of 40μA. A voltage of 2V~10V is required to drain this analog switch from a single voltage supply. A voltage higher than 30mA may cause damage to the switch multiplexer. As far as the outputs go, this switch multiplexer utilizes SEPARATE OUTPUT of them. There is a voltage range of 5V operating voltages for the electrical part. Among the inputs that can be operated are the 2 inputs.
74HC2G66GD,125 Features
Switch Circuit: SPST - NO
40μA Supply Current
-3db Bandwidth: 200MHz
74HC2G66GD,125 Applications
There are a lot of Nexperia USA Inc. 74HC2G66GD,125 Analog Switches & Multiplexers ICs applications.
- Access Concentrators
- ATM
- CSU
- Private Branch Exchange (PBX)
- High-Voltage
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- Medical systems
- Communication systems
- Industrial and process control systems
- Public switching systems
