74HC374DB,112
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SSOP (0.209, 5.30mm Width) |
| Number of Pins | 20 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tube |
| Series | 74HC |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Type | D-Type |
| Technology | CMOS |
| Voltage - Supply | 2V~6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | 74HC374 |
| Function | Standard |
| Output Type | Tri-State, Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 6V |
| Supply Voltage-Min (Vsup) | 2V |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Number of Bits | 8 |
| Clock Frequency | 83MHz |
| Propagation Delay | 250 ns |
| Quiescent Current | 8μA |
| Turn On Delay Time | 14 ns |
| Family | HC/UH |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 4μA |
| Output Characteristics | 3-STATE |
| Current - Output High, Low | 7.8mA 7.8mA |
| Max Propagation Delay @ V, Max CL | 28ns @ 6V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 3.5pF |
| Number of Input Lines | 8 |
| Clock Edge Trigger Type | Positive Edge |
| Height Seated (Max) | 2mm |
| Length | 7.2mm |
| Width | 5.3mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
74HC374DB,112 Overview
It is packaged in the way of 20-SSOP (0.209, 5.30mm Width). The package Tubecontains it. This output is configured with Tri-State, Non-Inverted. This trigger is configured to use Positive Edge. In this case, the electronic component is mounted in the way of Surface Mount. The JK flip flop operates with an input voltage of 2V~6V volts. A temperature of -40°C~125°C TAis considered to be the operating temperature. D-Typeis the type of this D latch. In terms of FPGAs, it belongs to the 74HC series. A frequency of 83MHzshould not be exceeded by its output. The element count is 1 . Despite external influences, it consumes 4μAof quiescent current. Currently, there are 20 terminations. It is a member of the 74HC374 family. Power is provided by a 5V supply. A JK flip flop with a 3.5pFfarad input capacitance is used here. In this case, the D flip flop belongs to the HC/UHfamily. The electronic part is mounted in the way of Surface Mount. A total of 20pins are provided on this board. This device has the clock edge trigger type of Positive Edge. This flip flop is designed with 8 Bits. It reaches 6Vwhen the maximum supply voltage (Vsup) is applied. A normal operating voltage (Vsup) should remain above 2V. The flip flop has 2ports embedded within it. If high efficiency is to be achieved, the supply voltage should be maintained at 5V. It is reported that there are 8 input lines. It consumes 8μA current.
74HC374DB,112 Features
Tube package
74HC series
20 pins
8 Bits
74HC374DB,112 Applications
There are a lot of Nexperia USA Inc. 74HC374DB,112 Flip Flops applications.
- ESD performance
- EMI reduction circuitry
- Functionally equivalent to the MC10/100EL29
- Pattern generators
- Balanced 24 mA output drivers
- Storage Registers
- Cold spare funcion
- Frequency division
- Balanced Propagation Delays
- Load Control
