74HC374PW,118
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 20 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74HC |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Type | D-Type |
| Technology | CMOS |
| Voltage - Supply | 2V~6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | 74HC374 |
| Function | Standard |
| Output Type | Tri-State, Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 6V |
| Supply Voltage-Min (Vsup) | 2V |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Number of Bits | 8 |
| Clock Frequency | 83MHz |
| Propagation Delay | 250 ns |
| Quiescent Current | 8μA |
| Turn On Delay Time | 14 ns |
| Family | HC/UH |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 4μA |
| Output Characteristics | 3-STATE |
| Current - Output High, Low | 7.8mA 7.8mA |
| Max Propagation Delay @ V, Max CL | 28ns @ 6V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 3.5pF |
| Number of Input Lines | 8 |
| Clock Edge Trigger Type | Positive Edge |
| Length | 6.5mm |
| Width | 4.4mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
74HC374PW,118 Overview
The flip flop is packaged in a case of 20-TSSOP (0.173, 4.40mm Width). A package named Tape & Reel (TR)includes it. Currently, the output is configured to use Tri-State, Non-Inverted. Positive Edgeis the trigger it is configured with. There is an electrical part that is mounted in the way of Surface Mount. Powered by a 2V~6Vvolt supply, it operates as follows. -40°C~125°C TAis the operating temperature. This D latch has the type D-Type. FPGAs belonging to the 74HCseries contain this type of chip. A frequency of 83MHzshould not be exceeded by its output. A total of 1elements are contained within it. During its operation, it consumes 4μA quiescent energy. Currently, there are 20 terminations. It is a member of the 74HC374 family. A voltage of 5V provides power to the D latch. A 3.5pFfarad input capacitance is provided by this T flip flop. In this case, the D flip flop belongs to the HC/UHfamily. There is an electronic part that is mounted in the way of Surface Mount. There are 20pins on it. In this device, the clock edge trigger type is Positive Edge. It is designed with a number of bits of 8. It reaches 6Vwhen the supply voltage is maximal (Vsup). For normal operation, the supply voltage (Vsup) should be above 2V. A D flip flop with 2embedded ports is available. For high efficiency, the supply voltage should be set to 5V. Currently, there are 8 input lines present. This D latch consumes 8μA quiescent current at all.
74HC374PW,118 Features
Tape & Reel (TR) package
74HC series
20 pins
8 Bits
74HC374PW,118 Applications
There are a lot of Nexperia USA Inc. 74HC374PW,118 Flip Flops applications.
- Buffer registers
- Frequency Divider circuits
- Convert a momentary switch to a toggle switch
- 2 – Bit synchronous counter
- Set-reset capability
- ESD protection
- Automotive
- Test & Measurement
- Frequency division
- Latch-up performance
