74HC377D-Q100J
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 20 |
| Supplier Device Package | 20-SO |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74HC |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Type | D-Type |
| Max Operating Temperature | 125°C |
| Min Operating Temperature | -40°C |
| Voltage - Supply | 2V~6V |
| Frequency | 83MHz |
| Base Part Number | 74HC377 |
| Function | Standard |
| Output Type | Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Number of Circuits | 8 |
| Max Supply Voltage | 6V |
| Min Supply Voltage | 2V |
| Clock Frequency | 83MHz |
| Propagation Delay | 27 ns |
| Quiescent Current | 8μA |
| Turn On Delay Time | 13 ns |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 8μA |
| Current - Output High, Low | 5.2mA 5.2mA |
| Number of Bits per Element | 8 |
| Max Propagation Delay @ V, Max CL | 27ns @ 6V, 50pF |
| Trigger Type | Positive Edge |
| High Level Output Current | 5.2mA |
| Input Capacitance | 3.5pF |
| Low Level Output Current | 5.2mA |
| Number of Input Lines | 8 |
| Number of Output Lines | 8 |
| Clock Edge Trigger Type | Positive Edge |
| RoHS Status | ROHS3 Compliant |
74HC377D-Q100J Overview
It is packaged in the way of 20-SOIC (0.295, 7.50mm Width). Package Tape & Reel (TR)embeds it. T flip flop uses Non-Invertedas the output. It is configured with a trigger that uses a value of Positive Edge. Surface Mountis occupied by this electronic component. The JK flip flop operates with an input voltage of 2V~6V volts. A temperature of -40°C~125°C TAis used in the operation. This D latch has the type D-Type. JK flip flop is a part of the 74HCseries of FPGAs. It should not exceed 83MHzin its output frequency. In total, there are 1 elements. As a result, it consumes 8μA quiescent current and is not affected by external forces. The 74HC377family includes it. The input capacitance of this JK flip flopis 3.5pF farads. Electronic part Surface Mountis mounted in the way. As you can see from the design, it has pins with 20. This device has Positive Edgeas its clock edge trigger type. Its superior flexibility is attributed to its use of 8 circuits. A high level of efficiency can be achieved by maintaining the supply voltage at 5V. There are 8 output lines in this JK flip flop. This input has 8lines. It consumes 8μA current. The high level output current is set to 5.2mA. Low level output current is set to 5.2mA. Temperatures below 125°Care ideal for operating. If the operating temperature is higher than -40°C, the system should operate properly. In order for it to operate, a supply voltage of 2Vis required. In this case, it supports a maximum supply voltage of 6V. This can be achieved at a frequency of 83MHz.
74HC377D-Q100J Features
Tape & Reel (TR) package
74HC series
20 pins
74HC377D-Q100J Applications
There are a lot of Nexperia USA Inc. 74HC377D-Q100J Flip Flops applications.
- Single Down Count-Control Line
- Count Modes
- Registers
- Test & Measurement
- Shift registers
- QML qualified product
- CMOS Process
- Consumer
- Event Detectors
- Frequency Dividers
