74HC377PW-Q100J
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 20 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74HC |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Type | D-Type |
| Technology | CMOS |
| Voltage - Supply | 2V~6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Base Part Number | 74HC377 |
| Function | Standard |
| Output Type | Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Supply Voltage-Max (Vsup) | 6V |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Bits | 8 |
| Clock Frequency | 83MHz |
| Propagation Delay | 27 ns |
| Quiescent Current | 8μA |
| Family | HC/UH |
| Logic Function | D-Type, Flip-Flop |
| Current - Output High, Low | 5.2mA 5.2mA |
| Output Polarity | TRUE |
| Max Propagation Delay @ V, Max CL | 27ns @ 6V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 3.5pF |
| Number of Input Lines | 8 |
| fmax-Min | 24 MHz |
| Clock Edge Trigger Type | Positive Edge |
| Length | 6.5mm |
| Width | 4.4mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
74HC377PW-Q100J Overview
As a result, it is packaged as 20-TSSOP (0.173, 4.40mm Width). There is an embedded version in the package Tape & Reel (TR). T flip flop is configured with an output of Non-Inverted. JK flip flop uses Positive Edgeas the trigger. Surface Mountis positioned in the way of this electronic part. The JK flip flop operates at 2V~6Vvolts. A temperature of -40°C~125°C TAis used in the operation. D-Typeis the type of this D latch. In terms of FPGAs, it belongs to the 74HC series. Its output frequency should not exceed 83MHz Hz. A total of 1elements are present in it. It has been determined that there have been 20 terminations. The 74HC377 family contains this object. The D flip flop is powered by a voltage of 5V . Its input capacitance is 3.5pFfarads. Electronic devices of this type belong to the HC/UHfamily. A part of the electronic system is mounted in the way of Surface Mount. A total of 20pins are provided on this board. There is a clock edge trigger type of Positive Edgeon this device. There are 8bits in its design. It reaches 6Vwhen the maximum supply voltage (Vsup) is applied. Normally, the supply voltage (Vsup) should be kept above 2V. If high efficiency is desired, the supply voltage should be kept at 5V. Currently, there are 8 lines of input. Despite external influences, it consumes 8μAof quiescent current.
74HC377PW-Q100J Features
Tape & Reel (TR) package
74HC series
20 pins
8 Bits
74HC377PW-Q100J Applications
There are a lot of Nexperia USA Inc. 74HC377PW-Q100J Flip Flops applications.
- Supports Live Insertion
- Load Control
- Pattern generators
- Clock pulse
- Consumer
- Counters
- Balanced Propagation Delays
- Balanced 24 mA output drivers
- Frequency Dividers
- Frequency division
