74HC4016D,653
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 14 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2013 |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| Resistance | 135Ohm |
| Max Power Dissipation | 500mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 9V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | 74HC4016 |
| Pin Count | 14 |
| Operating Supply Voltage | 5V |
| Polarity | Non-Inverting |
| Number of Channels | 1 |
| Max Supply Voltage | 10V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 1nA |
| Power Dissipation | 500mW |
| Throw Configuration | SPST |
| Turn On Delay Time | 190 ns |
| Number of Inputs | 4 |
| Supply Type | Single |
| Turn-Off Delay Time | 145 ns |
| -3db Bandwidth | 160MHz |
| On-State Resistance (Max) | 120Ohm |
| High Level Output Current | 25mA |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 50 dB |
| Current - Leakage (IS(off)) (Max) | 1μA |
| Channel Capacitance (CS(off), CD(off)) | 3.5pF |
| On-state Resistance Match-Nom | 9Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 28ns, 22ns |
| Channel-to-Channel Matching (ΔRon) | 9 Ω |
| Crosstalk | -60dB @ 1MHz |
| Switch-on Time-Max | 28ns |
| Switch-off Time-Max | 22ns |
| Voltage - Supply, Single (V+) | 2V~10V |
| Height Seated (Max) | 1.75mm |
| Length | 8.65mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
74HC4016D,653 Overview
The electronic component is convenient to ship overseas because it is packed in a 14-SOIC (0.154, 3.90mm Width). In order to provide high reliability, an advanced packaging method Tape & Reel (TR) is used. It is mounted in the position Surface Mount. Multiplexers and demultiplexers have a number of circuits 1:1. The operating temperature is extended to around -40°C~125°C TA. In total, there are 14 terminations. Due to its 1 channels, the electrical component produces high-quality output. If the voltage supply is 9V volts, the electrical component should be turned on and run. It is injected into the electrical part body with 14 pins. Unlike digital switches, these are based on SPST - NO switching circuits. Try searching for the analog switch ic with 74HC4016 if you are looking for variants. There is 135Ohm internal resistance in this digital multiplexer. To find out what the functions of 14 pins are, please refer to their datasheets. An abnormal situation would be for the switch device to be supplied with a voltage greater than 10V. The analog switch ic is of the Single supply type and is cost-effective. The lowest voltage the electronic part should receive is 2V. This digital switch can be operated with a current of 1nA. Using a single voltage supply, this switch device consumes 2V~10V volts. Operating voltages range from 5V. The electrical component supports 4 inputs.
74HC4016D,653 Features
1 Channels
Switch Circuit: SPST - NO
1nA Supply Current
-3db Bandwidth: 160MHz
74HC4016D,653 Applications
There are a lot of Nexperia USA Inc. 74HC4016D,653 Analog Switches & Multiplexers ICs applications.
- Intelligent PBX
- Industrial and process control systems
- Data switching
- PBXs
- Cable PC
- FTTH
- Audio signal routing
- E1 Multiplexer
- Microprocessor Controlled Analog Systems
- Cellular phones
