74HC4016PW,112
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 14 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tube |
| Published | 2013 |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| Resistance | 135Ohm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Max Power Dissipation | 500mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 9V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | 74HC4016 |
| Pin Count | 14 |
| Operating Supply Voltage | 5V |
| Number of Channels | 1 |
| Max Supply Voltage | 10V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 1nA |
| Power Dissipation | 500mW |
| Throw Configuration | SPST |
| Turn On Delay Time | 190 ns |
| Number of Inputs | 4 |
| Supply Type | Single |
| Turn-Off Delay Time | 145 ns |
| -3db Bandwidth | 160MHz |
| On-State Resistance (Max) | 120Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 50 dB |
| Current - Leakage (IS(off)) (Max) | 1μA |
| Channel Capacitance (CS(off), CD(off)) | 3.5pF |
| On-state Resistance Match-Nom | 9Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 28ns, 22ns |
| Channel-to-Channel Matching (ΔRon) | 9 Ω |
| Crosstalk | -60dB @ 1MHz |
| Switch-on Time-Max | 28ns |
| Switch-off Time-Max | 22ns |
| Voltage - Supply, Single (V+) | 2V~10V |
| Height Seated (Max) | 1.1mm |
| Length | 5mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
74HC4016PW,112 Overview
As the electronic part is packed in 14-TSSOP (0.173, 4.40mm Width), international shipping is convenient. High reliability is provided by advanced packaging method Tube. There is an analog multiplexer mounted in position Surface Mount. Multiplexers and demultiplexers have a number of circuits 1:1. Around -40°C~125°C TA is the extended operating temperature. The total number of terminations is 14. High-quality output is provided by the electronic component's 1 channels. In the case of a voltage supply of 9V volts, the electrical part can be powered up and run. The electronic part body is injected with 14 pins. A SPST - NO switching circuit is used to build these analog multiplexers. Using the 74HC4016 search parameter, you can discover variants of the switch. As far as internal resistance is concerned, it has 135Ohm. The datasheets for the 14 pins explain the functions. It is normally recommended that users do not supply the multiplexer with voltages higher than 10V. Analog switch ics with Single supply type are cost-effective. 2V is the lowest voltage that should be fed to the electronic electronic part. 1nA current would be enough for this multiplexer to operate. Draining from a single voltage supply, this analog switch requires a voltage of 2V~10V. 5V operating voltages are supported by the electronic component. In order to operate the 4 inputs, there are several steps to follow.
74HC4016PW,112 Features
1 Channels
Switch Circuit: SPST - NO
1nA Supply Current
-3db Bandwidth: 160MHz
74HC4016PW,112 Applications
There are a lot of Nexperia USA Inc. 74HC4016PW,112 Analog Switches & Multiplexers ICs applications.
- SDH/SONET multiplexers
- SONET/SDH ADM
- Industrial
- Cross Connects
- Voice over IP/DSL – Integrated Access Devices, Smart
- MP3 players
- Audio/video switches
- Fault Tolerant Systems
- Routers
- Relay Replacement
