Parameters |
Radiation Hardening |
No |
REACH SVHC |
No SVHC |
RoHS Status |
ROHS3 Compliant |
Factory Lead Time |
1 Week |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
16-TSSOP (0.173, 4.40mm Width) |
Number of Pins |
16 |
Weight |
172.98879mg |
Operating Temperature |
-40°C~125°C TA |
Packaging |
Tape & Reel (TR) |
Published |
1999 |
Series |
Automotive, AEC-Q100 |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Resistance |
140Ohm |
Max Power Dissipation |
500mW |
Base Part Number |
74HC4051 |
Pin Count |
16 |
Number of Circuits |
1 |
Max Supply Voltage |
10V |
Min Supply Voltage |
2V |
Operating Supply Current |
16μA |
Power Dissipation |
500mW |
Propagation Delay |
90 ns |
Turn On Delay Time |
60 ns |
Logic Function |
Demultiplexer, Multiplexer |
Voltage - Supply, Single/Dual (±) |
2V~10V ±1.5V~5V |
Supply Type |
Dual, Single |
Max Dual Supply Voltage |
5V |
-3db Bandwidth |
180MHz |
On-State Resistance (Max) |
120Ohm |
Min Dual Supply Voltage |
1V |
Dual Supply Voltage |
2.5V |
Multiplexer/Demultiplexer Circuit |
8:1 |
Current - Leakage (IS(off)) (Max) |
400nA |
Channel Capacitance (CS(off), CD(off)) |
3.5pF |
Switch Time (Ton, Toff) (Max) |
51ns, 42ns |
Number of Output Lines |
8 |
Channel-to-Channel Matching (ΔRon) |
6 Ω |
Drain to Source Resistance |
180Ohm |
74HC4051PW-Q100,11 Overview
Shipping overseas is convenient due to the electrical component's packing in 16-TSSOP (0.173, 4.40mm Width). Advanced packaging method Tape & Reel (TR) is used to provide high reliability. It is mounted in the position Surface Mount. 8:1 is the number of circuits in the multiplexer and demultiplexer. The operating temperature is extended to around -40°C~125°C TA. There are 16 pins injected into the electronic part body. There are 1 circuits in this multiplexer. Try searching with 74HC4051 if you're looking for variants. Internally, this switch multiplexer has a resistance of 140Ohm. To find out what the 16 pins do, please refer to the datasheets. An abnormal situation would be for the switch device to be supplied with a voltage greater than 10V. Analogue multiplexer with a Dual, Single supply type that is cost-effective. It is recommended that the electrical component receives a voltage of 2V. An operating current of 16μA would be sufficient for this switch device. If put voltage greater than 5V on the multiplexer, damage may be caused to the device. When using dual power supplies, you should attach at least 1V. The Drain to Source resistance of this electronic component is 180Ohm. This is one of the Automotive, AEC-Q100 series.
74HC4051PW-Q100,11 Features
16μA Supply Current
-3db Bandwidth: 180MHz
Drain-to-Source resistance: 180Ohm
74HC4051PW-Q100,11 Applications
There are a lot of Nexperia USA Inc. 74HC4051PW-Q100,11 Analog Switches & Multiplexers ICs applications.
- FTTH
- Switching Systems
- Intelligent PBX
- SONET
- Access Concentrators
- Audio signal routing
- SONET/SDH ADM
- Mechanical reed relay replacement
- Fault Tolerant Systems
- 65 V DACs