Parameters |
Factory Lead Time |
1 Week |
Contact Plating |
Gold |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
16-VFQFN Exposed Pad |
Number of Pins |
16 |
Operating Temperature |
-40°C~125°C TA |
Packaging |
Tape & Reel (TR) |
Published |
2013 |
JESD-609 Code |
e4 |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
Resistance |
140Ohm |
Max Power Dissipation |
500mW |
Technology |
CMOS |
Terminal Position |
QUAD |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
3 |
Supply Voltage |
5V |
Terminal Pitch |
0.5mm |
Time@Peak Reflow Temperature-Max (s) |
30 |
Base Part Number |
74HC4053 |
Pin Count |
16 |
Operating Supply Voltage |
5V |
Number of Channels |
1 |
Number of Circuits |
3 |
Max Supply Voltage |
10V |
Min Supply Voltage |
2V |
Operating Supply Current |
16μA |
Power Dissipation |
500mW |
Propagation Delay |
4 ns |
Turn On Delay Time |
220 ns |
Logic Function |
Demultiplexer, Demux, Multiplexer, Mux |
Number of Inputs |
6 |
Voltage - Supply, Single/Dual (±) |
2V~10V ±1.5V~5V |
Supply Type |
Dual, Single |
Bandwidth |
170MHz |
Turn-Off Delay Time |
210 ns |
Max Dual Supply Voltage |
5V |
On-State Resistance (Max) |
120Ohm |
Min Dual Supply Voltage |
1V |
High Level Output Current |
25mA |
Dual Supply Voltage |
2.5V |
Low Level Output Current |
25mA |
Multiplexer/Demultiplexer Circuit |
2:1 |
Off-state Isolation-Nom |
50 dB |
Current - Leakage (IS(off)) (Max) |
100nA |
Channel Capacitance (CS(off), CD(off)) |
3.5pF |
On-state Resistance Match-Nom |
8Ohm |
Switch Circuit |
SPDT |
Switch Time (Ton, Toff) (Max) |
31ns, 29ns |
Channel-to-Channel Matching (ΔRon) |
6 Ω |
Crosstalk |
-60dB @ 1MHz |
Height Seated (Max) |
1mm |
Radiation Hardening |
No |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
74HC4053BQ,115 Overview
As the electronic part is packed in 16-VFQFN Exposed Pad, international shipping is convenient. The advanced packaging method Tape & Reel (TR) provides high reliability. Multiplexers like this are mounted in the Surface Mount position. Multiplexers and demultiplexers have the same number of circuits 2:1. Operation at a temperature around -40°C~125°C TA. There are 16 terminations totally. A high-quality output is provided by the electrical component's 1 channels. If the voltage supply is 5V volts, the electrical component should be turned on and run. 16 pins are injected to the electronic part body. On the other hand, analog switches can be constructed using SPDT switching circuits. Circuits number 3 make up this analogue multiplexer. Try searching for 74HC4053 variants of the analog switch ic. It has an internal resistance of 140Ohm. Please refer to the datasheets for 16 pins functions. normally, users should not supply switches with voltages higher than 10V. Analogue multiplexer with a Dual, Single supply type that is cost-effective. There should be 2V voltage fed to the electrical part below 2V. The analogue multiplexer could operate on 16μA current. It is possible to supply this switch device with dual voltages. However, it is not advisable to exceed 5V. When using dual power supplies, you should attach at least 1V. Operating voltages of 5V are compatible with the electrical part. Operating 6 inputs is required. 170MHz-bandwidths can be used to transfer data between multiplexers.
74HC4053BQ,115 Features
1 Channels
Switch Circuit: SPDT
16μA Supply Current
Bandwidth: 170MHz
74HC4053BQ,115 Applications
There are a lot of Nexperia USA Inc. 74HC4053BQ,115 Analog Switches & Multiplexers ICs applications.
- Mechanical reed relay replacement
- Automatic test equipment
- Audio/video switches
- Digital Cross-Connects
- Isolation
- Transmit
- Industrial and process control systems
- SDH/SONET multiplexers
- Audio signal routing
- HDTV