74HC4053DB,118
| Parameters | |
|---|---|
| Number of Pins | 16 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2013 |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 140Ohm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 3 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | 74HC4053 |
| Pin Count | 16 |
| Number of Outputs | 3 |
| Operating Supply Voltage | 5V |
| Number of Channels | 1 |
| Max Supply Voltage | 10V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 16μA |
| Power Dissipation | 500mW |
| Propagation Delay | 60 ns |
| Logic Function | Demultiplexer, Multiplexer |
| Voltage - Supply, Single/Dual (±) | 2V~10V ±1.5V~5V |
| Supply Type | Dual, Single |
| Max Dual Supply Voltage | 5V |
| -3db Bandwidth | 170MHz |
| On-State Resistance (Max) | 120Ohm |
| Min Dual Supply Voltage | 1V |
| Dual Supply Voltage | 2.5V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 50 dB |
| Number of Input Lines | 6 |
| Current - Leakage (IS(off)) (Max) | 100nA |
| Channel Capacitance (CS(off), CD(off)) | 3.5pF |
| On-state Resistance Match-Nom | 8Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 31ns, 29ns |
| Channel-to-Channel Matching (ΔRon) | 6 Ω |
| Crosstalk | -60dB @ 1MHz |
| Height Seated (Max) | 2mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SSOP (0.209, 5.30mm Width) |
74HC4053DB,118 Overview
Packed in 16-SSOP (0.209, 5.30mm Width), the electronic component is convenient for shipping overseas. High reliability is provided by advanced packaging method Tape & Reel (TR). It is mounted in the position Surface Mount. Multiplexers and demultiplexers have a ratio of 2:1. Extended operating temperature around -40°C~125°C TA. A total of 16 terminations have been recorded. High-quality output is provided by the electronic component's 1 channels. If the voltage supply is 5V volts, the electrical component should be turned on and run. As part of the design of the 16 series, this electronic part has been incorporated into the system. Multiplexers built on a SPDT switching circuit are built. Using the 74HC4053 search parameter, you can discover variants of the switch. The internal resistance of this digital multiplexer is 140Ohm. Datasheets for 16 pin functions are available upon request. It is normally recommended that users do not supply the multiplexer with voltages higher than 10V. The digital multiplexer has a low cost Dual, Single supply. In order for the electronic part to function properly, the lowest voltage should be 2V. 16μA current would be enough for this multiplexer to operate. For this multiplexer, dual supply voltage is feasible, but it should not exceed 5V. When using dual power supplies, you should attach at least 1V. Operating voltages of 5V are compatible with the electrical part. An output of 3 is provided by the digital multiplexer.
74HC4053DB,118 Features
1 Channels
Switch Circuit: SPDT
16μA Supply Current
-3db Bandwidth: 170MHz
74HC4053DB,118 Applications
There are a lot of Nexperia USA Inc. 74HC4053DB,118 Analog Switches & Multiplexers ICs applications.
- Battery Powered Instruments
- PBXs
- Cell phones
- Remote wireless modules
- Communication systems
- USB 1.1 signal switching circuits
- ATM
- Avionics
- Central office
- Cable Telephony – NIU, Set-Top Box, Home Side Box
