74HC4053PW-Q100,11
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 16 |
| Weight | 172.98879mg |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2010 |
| Series | Automotive, AEC-Q100 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Resistance | 140Ohm |
| Max Power Dissipation | 500mW |
| Base Part Number | 74HC4053 |
| Pin Count | 16 |
| Number of Circuits | 3 |
| Max Supply Voltage | 10V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 16μA |
| Power Dissipation | 500mW |
| Propagation Delay | 60 ns |
| Turn On Delay Time | 90 ns |
| Logic Function | Demultiplexer, Multiplexer |
| Number of Inputs | 6 |
| Voltage - Supply, Single/Dual (±) | 2V~10V ±1.5V~5V |
| Supply Type | Dual, Single |
| Max Dual Supply Voltage | 5V |
| -3db Bandwidth | 170MHz |
| On-State Resistance (Max) | 120Ohm |
| Min Dual Supply Voltage | 1V |
| Dual Supply Voltage | 2.5V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Number of Input Lines | 2 |
| Current - Leakage (IS(off)) (Max) | 100nA |
| Channel Capacitance (CS(off), CD(off)) | 3.5pF |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 31ns, 29ns |
| Channel-to-Channel Matching (ΔRon) | 6 Ω |
| Crosstalk | -60dB @ 1MHz |
| Drain to Source Resistance | 180Ohm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
74HC4053PW-Q100,11 Overview
Shipping overseas is convenient due to the electrical component's packing in 16-TSSOP (0.173, 4.40mm Width). High reliability is achieved by using advanced packaging method Tape & Reel (TR). This analog switch is mounted in Surface Mount. 2:1 is the ratio between multiplexers and demultiplexers. Around -40°C~125°C TA is the extended operating temperature. An electrical component like this is included in the 16 series. Circuits based on SPDT switching are used to construct these analog switch ics. There are 3 circuits in this multiplexer. Try searching for the analog switch ic with 74HC4053 if you are looking for variants. There is 140Ohm internal resistance in this digital multiplexer. The functions of 16 pins can be found in the datasheets. In a normalsituation, users should not supply the switches with voltage higher than 10V. Dual, Single supply type digital switch with a low cost. It is recommended that the electrical component receives a voltage of 2V. This digital switch can be operated with a current of 16μA. Despite this switch's dual supply capability, its voltage should not exceed 5V. You should attach at least 1V voltage if you are using dual power supply. Operating the 6 inputs requires 6 inputs. It has a Drain to Source resistance of 180Ohm ohms. It belongs to the series Automotive, AEC-Q100.
74HC4053PW-Q100,11 Features
Switch Circuit: SPDT
16μA Supply Current
-3db Bandwidth: 170MHz
Drain-to-Source resistance: 180Ohm
74HC4053PW-Q100,11 Applications
There are a lot of Nexperia USA Inc. 74HC4053PW-Q100,11 Analog Switches & Multiplexers ICs applications.
- Isolation
- Imaging
- CSU
- Power routing
- Battery-powered systems
- Residential Gateways, Home Gateway/Router
- Frame Relay Equipment
- Intelligent PBX
- HDTV
- High-Voltage
