74HC4066BQ,115
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-VFQFN Exposed Pad |
| Number of Pins | 14 |
| Weight | 113.398093g |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2013 |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| Resistance | 128Ohm |
| Max Power Dissipation | 500mW |
| Technology | CMOS |
| Terminal Position | QUAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 4.5V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | 74HC4066 |
| Pin Count | 14 |
| Operating Supply Voltage | 5V |
| Polarity | Non-Inverting |
| Number of Channels | 1 |
| Max Supply Voltage | 10V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 40μA |
| Power Dissipation | 500mW |
| Turn On Delay Time | 36 ns |
| Logic Function | Demultiplexer, Multiplexer |
| Number of Inputs | 4 |
| Supply Type | Single |
| Turn-Off Delay Time | 44 ns |
| -3db Bandwidth | 200MHz |
| On-State Resistance (Max) | 95Ohm |
| High Level Output Current | 25mA |
| Low Level Output Current | 25mA |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 50 dB |
| Current - Leakage (IS(off)) (Max) | 1μA |
| Channel Capacitance (CS(off), CD(off)) | 3.5pF |
| On-state Resistance Match-Nom | 5Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 30ns, 20ns |
| Channel-to-Channel Matching (ΔRon) | 3 Ω |
| Crosstalk | -60dB @ 1MHz |
| Switch-on Time-Max | 30ns |
| Voltage - Supply, Single (V+) | 2V~10V |
| Drain to Source Resistance | 142Ohm |
| Height | 6.35mm |
| Length | 6.35mm |
| Width | 6.35mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
74HC4066BQ,115 Overview
As the electronic part is packed in 14-VFQFN Exposed Pad, international shipping is convenient. This packaging method provides high reliability because it uses advanced packaging techniques. Multiplexers like this are mounted in the Surface Mount position. 1:1 is the ratio of multiplexer to demultiplexer circuits. Operating temperature around -40°C~125°C TA extended. Total terminations are 14. By its 1 channels, the electronic component provides high-quality output. Turning on and running the electrical part should be easy with a 4.5V voltage supply. This electronic part can be found in the 14 series. Multiplexers built on a SPST - NO switching circuit are built. Try searching for 74HC4066 variants of the analog switch ic. As far as internal resistance is concerned, it has 128Ohm. The functions of 14 pins can be found in the datasheets. It is generally not recommended to supply a voltage higher than 10V to the switch device in normal circumstances. A cost-effective Single supply type analogue multiplexer. In order for the electronic part to function properly, the lowest voltage should be 2V. An operating current of 40μA would be sufficient for this switch device. The voltage required by this switch device is 2V~10V, draining from a single voltage supply. Operating voltages range from 5V. The electrical component supports 4 inputs. There is 142Ohm resistance between Drain and Source for this electronic part.
74HC4066BQ,115 Features
1 Channels
Switch Circuit: SPST - NO
40μA Supply Current
-3db Bandwidth: 200MHz
Drain-to-Source resistance: 142Ohm
74HC4066BQ,115 Applications
There are a lot of Nexperia USA Inc. 74HC4066BQ,115 Analog Switches & Multiplexers ICs applications.
- Microwave transmission systems
- Medical systems
- Frame Relay Equipment
- Cellular phones
- Voice over IP/DSL – Integrated Access Devices, Smart
- Access Concentrators
- Intelligent PBX
- Precision instrumentation
- USB 1.1 signal switching circuits
- Fiber In The Loop (FITL)
