74HC4066DB,118
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-SSOP (0.209, 5.30mm Width) |
| Number of Pins | 14 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2008 |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| Resistance | 78Ohm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Max Power Dissipation | 500mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 4.5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | 74HC4066 |
| Pin Count | 14 |
| Operating Supply Voltage | 5V |
| Number of Channels | 1 |
| Max Supply Voltage | 10V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 40μA |
| Power Dissipation | 500mW |
| Turn On Delay Time | 36 ns |
| Logic Function | Demultiplexer, Multiplexer |
| Number of Inputs | 4 |
| Supply Type | Single |
| Turn-Off Delay Time | 44 ns |
| -3db Bandwidth | 200MHz |
| On-State Resistance (Max) | 95Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 50 dB |
| Current - Leakage (IS(off)) (Max) | 1μA |
| Channel Capacitance (CS(off), CD(off)) | 3.5pF |
| On-state Resistance Match-Nom | 5Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 30ns, 20ns |
| Channel-to-Channel Matching (ΔRon) | 3 Ω |
| Crosstalk | -60dB @ 1MHz |
| Switch-on Time-Max | 30ns |
| Voltage - Supply, Single (V+) | 2V~10V |
| Height Seated (Max) | 2mm |
| Length | 6.2mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
74HC4066DB,118 Overview
The electronic part can be shipped overseas conveniently because it is packaged in 14-SSOP (0.209, 5.30mm Width). To ensure high reliability, a new packaging method Tape & Reel (TR) is used. The multiplexer is located in Surface Mount. 1:1 is the ratio of multiplexer to demultiplexer circuits. Operational temperature extended around -40°C~125°C TA. Total terminations are 14. By its 1 channels, the electronic component provides high-quality output. In the case of a voltage supply of 4.5V volts, the electrical part can be powered up and run. As part of its design, the 14 series is equipped with this electronic component. These analog multiplexers are built based on SPST - NO switching circuits. Look for analog switch ic variants by searching with 74HC4066. As far as internal resistance is concerned, it has 78Ohm. For functions related to 14 pins, please refer to the datasheets. A voltage higher than 10V should not normally be supplied to the switches. Digital switch that provides Single power at a cost-effective price. In order for the electronic part to function properly, the lowest voltage should be 2V. An operating current of 40μA would be sufficient for this switch device. Draining from a single voltage supply, this analog switch requires a voltage of 2V~10V. It can operate from 5V operating voltages. In order to operate the 4 inputs, there are several steps to follow.
74HC4066DB,118 Features
1 Channels
Switch Circuit: SPST - NO
40μA Supply Current
-3db Bandwidth: 200MHz
74HC4066DB,118 Applications
There are a lot of Nexperia USA Inc. 74HC4066DB,118 Analog Switches & Multiplexers ICs applications.
- Avionics test equipment
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- High-Voltage
- 65 V DACs
- Battery-powered systems
- Sample-and-hold systems
- SONET/SDH ADM
- HDTV
- Sample hold systems
- Data Acquisition Systems
