74HC4066PW-Q100,11
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 14 |
| Weight | 140.30179mg |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2011 |
| Series | Automotive, AEC-Q100 |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| Resistance | 128Ohm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Max Power Dissipation | 500mW |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Base Part Number | 74HC4066 |
| Pin Count | 14 |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 10V |
| Min Supply Voltage | 2V |
| Analog IC - Other Type | DIFFERENTIAL MULTIPLEXER |
| Operating Supply Current | 40μA |
| Power Dissipation | 100mW |
| Propagation Delay | 90 ns |
| Turn On Delay Time | 90 ns |
| Logic Function | Demultiplexer, Multiplexer |
| Supply Type | Single |
| -3db Bandwidth | 200MHz |
| On-State Resistance (Max) | 95Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 50 dB |
| Number of Input Lines | 2 |
| Current - Leakage (IS(off)) (Max) | 1μA |
| Channel Capacitance (CS(off), CD(off)) | 3.5pF |
| On-state Resistance Match-Nom | 5Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 30ns, 20ns |
| Channel-to-Channel Matching (ΔRon) | 3 Ω |
| Crosstalk | -60dB @ 1MHz |
| Switch-on Time-Max | 150ns |
| Voltage - Supply, Single (V+) | 2V~10V |
| Drain to Source Resistance | 105Ohm |
| Height Seated (Max) | 1.1mm |
| Length | 5mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
74HC4066PW-Q100,11 Overview
As the electronic part is packed in 14-TSSOP (0.173, 4.40mm Width), international shipping is convenient. This packaging method provides high reliability because it uses advanced packaging techniques. In Surface Mount, this analog switch is mounted. 1:1 is the ratio between multiplexers and demultiplexers. Operation at a temperature around -40°C~125°C TA. The total number of terminations is 14. The electronic part provides high-quality output because it has 1 channels. A 5V voltage supply should turn on and run the electronic component. An electrical component like this is included in the 14 series. The analog switch ics are built using SPST - NO switching circuits. The circuits in this analogue multiplexer number 4. Try searching with 74HC4066 if you're looking for variants. An switch multiplexer with 128Ohm internal resistance has a value of 128Ohm. You can find the functions of the 14 pins in the datasheets. In normalcircumstances, users should not exceed 10V volts for the multiplexer. A analog switch ic that has a cost-effective Single supply type. It is recommended that the electrical component receives a voltage of 2V. The switch device would be able to operate with 40μA current. This analog switch requires a voltage of 2V~10V to drain from a single voltage supply. An analog IC with the number DIFFERENTIAL MULTIPLEXER is integrated into this board. There is 105Ohm resistance between Drain and Source for this electronic part. It comes from the Automotive, AEC-Q100 series.
74HC4066PW-Q100,11 Features
1 Channels
Switch Circuit: SPST - NO
40μA Supply Current
-3db Bandwidth: 200MHz
Drain-to-Source resistance: 105Ohm
74HC4066PW-Q100,11 Applications
There are a lot of Nexperia USA Inc. 74HC4066PW-Q100,11 Analog Switches & Multiplexers ICs applications.
- Communication systems
- Transmit
- Private Branch Exchange (PBX)
- Battery Powered Systems
- Public switching systems
- Precision instrumentation
- Audio signal routing
- High reliability control systems
- Digital access cross connects
- Fiber In The Loop (FITL)
