74HC4852BQ,115
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-VFQFN Exposed Pad |
| Number of Pins | 16 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 195Ohm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Max Power Dissipation | 500mW |
| Technology | CMOS |
| Terminal Position | QUAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | 74HC4852 |
| Pin Count | 16 |
| Number of Channels | 8 |
| Number of Circuits | 2 |
| Max Supply Voltage | 6V |
| Min Supply Voltage | 2V |
| Analog IC - Other Type | DIFFERENTIAL MULTIPLEXER |
| Operating Supply Current | 2μA |
| Power Dissipation | 500mW |
| Propagation Delay | 2.5 ns |
| Turn On Delay Time | 47.5 ns |
| Logic Function | Demultiplexer, Multiplexer |
| Supply Type | Single |
| Turn-Off Delay Time | 100 ns |
| On-State Resistance (Max) | 195Ohm |
| Multiplexer/Demultiplexer Circuit | 4:1 |
| Current - Leakage (IS(off)) (Max) | 100nA |
| Channel Capacitance (CS(off), CD(off)) | 10pF |
| On-state Resistance Match-Nom | 8Ohm |
| Switch Circuit | SP4T |
| Switch Time (Ton, Toff) (Max) | 39ns, 78ns |
| Channel-to-Channel Matching (ΔRon) | 3 Ω |
| Switch-on Time-Max | 57.5ns |
| Switch-off Time-Max | 115ns |
| Voltage - Supply, Single (V+) | 2V~6V |
| Height Seated (Max) | 1mm |
| Length | 3.5mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
74HC4852BQ,115 Overview
As the electronic part is packed in 16-VFQFN Exposed Pad, international shipping is convenient. A high level of reliability can be achieved through the use of an advanced packaging method Tape & Reel (TR). In Surface Mount, this analog switch is mounted. 4:1 is the ratio of multiplexer to demultiplexer circuits. Operation at a temperature around -40°C~125°C TA. 16 terminations have been made so far. A high-quality output is provided by the electrical component's 8 channels. An 3V voltage supply should allow the electrical part to be turned on and run. As part of its design, the 16 series is equipped with this electronic component. Circuits based on SP4T switching are used to construct these analog switch ics. A 2 circuit is present in this switch device. Try searching for 74HC4852 variants of the analog switch ic. As far as internal resistance is concerned, it has 195Ohm. The functions of 16 pins can be found in the datasheets. In a normalsituation, users should not supply the switches with voltage higher than 6V. A analog switch ic that has a cost-effective Single supply type. There should be 2V voltage fed to the electrical part below 2V. For this multiplexer to operate, 2μA current would be sufficient. A voltage of 2V~6V is required to drain this analog switch from a single voltage supply. Integrated with an analog IC DIFFERENTIAL MULTIPLEXER.
74HC4852BQ,115 Features
8 Channels
Switch Circuit: SP4T
2μA Supply Current
74HC4852BQ,115 Applications
There are a lot of Nexperia USA Inc. 74HC4852BQ,115 Analog Switches & Multiplexers ICs applications.
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- PBX interfaces
- Ultrasound
- PDAs
- Access Concentrators
- Relay replacements
- Industrial
- Precision instrumentation
- Digital Cross-Connects
- Cross Connects
