74HC4852D,118
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 195Ohm |
| Max Power Dissipation | 500mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | 74HC4852 |
| Pin Count | 16 |
| Number of Channels | 4 |
| Number of Circuits | 2 |
| Max Supply Voltage | 6V |
| Min Supply Voltage | 2V |
| Analog IC - Other Type | DIFFERENTIAL MULTIPLEXER |
| Operating Supply Current | 2μA |
| Power Dissipation | 500mW |
| Propagation Delay | 2.5 ns |
| Turn On Delay Time | 47.5 ns |
| Logic Function | Demultiplexer, Multiplexer |
| Number of Inputs | 8 |
| Supply Type | Single |
| Turn-Off Delay Time | 100 ns |
| On-State Resistance (Max) | 195Ohm |
| High Level Output Current | 25mA |
| Low Level Output Current | 25mA |
| Multiplexer/Demultiplexer Circuit | 4:1 |
| Current - Leakage (IS(off)) (Max) | 100nA |
| Channel Capacitance (CS(off), CD(off)) | 10pF |
| On-state Resistance Match-Nom | 8Ohm |
| Switch Circuit | SP4T |
| Switch Time (Ton, Toff) (Max) | 39ns, 78ns |
| Channel-to-Channel Matching (ΔRon) | 3 Ω |
| Switch-on Time-Max | 57.5ns |
| Switch-off Time-Max | 115ns |
| Voltage - Supply, Single (V+) | 2V~6V |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
74HC4852D,118 Overview
Shipping overseas is convenient with the electronic component packed in 16-SOIC (0.154, 3.90mm Width). High reliability is ensured by the advanced packaging method Tape & Reel (TR). The multiplexer is located in Surface Mount. 4:1 is the number of circuits in the multiplexer and demultiplexer. Operating temperature extended to -40°C~125°C TA. In total, there are 16 terminations. As a result of its 4 channels, this electronic component provides high-quality output. With a 3V voltage supply, the electrical component should be turned on and run. Into the electrical component body are injected 16 pins. On the other hand, analog switches can be constructed using SP4T switching circuits. A 2 circuit is present in this switch device. Search with 74HC4852 if you are looking for analog multiplexer variants. As far as internal resistance is concerned, it has 195Ohm. For details about the functions of 16 pins, please refer to the datasheets. In a normalsituation, users should not supply the switches with voltage higher than 6V. An effective Single supply digital multiplexer. 2V is the lowest voltage the electrical component should receive. 2μA current would be enough for this multiplexer to operate. This analogue multiplexer requires a voltage of 2V~6V when it drains from a single voltage supply. Integrated with DIFFERENTIAL MULTIPLEXER analog IC. In order to operate the 8 inputs, there are several steps to follow.
74HC4852D,118 Features
4 Channels
Switch Circuit: SP4T
2μA Supply Current
74HC4852D,118 Applications
There are a lot of Nexperia USA Inc. 74HC4852D,118 Analog Switches & Multiplexers ICs applications.
- Precision test equipment
- Battery Powered Systems
- PBX interfaces
- Fiber In The Loop (FITL)
- Automatic test equipment
- Residential Gateways, Home Gateway/Router
- RGB switches
- CSU
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Relay replacements
