74HC4852PW-Q100,11
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 16 |
| Weight | 172.98879mg |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Series | Automotive, AEC-Q100 |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 195Ohm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Max Power Dissipation | 500mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Number of Functions | 2 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.65mm |
| Base Part Number | 74HC4852 |
| Pin Count | 16 |
| Number of Channels | 4 |
| Number of Circuits | 2 |
| Max Supply Voltage | 6V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 2μA |
| Power Dissipation | 500mW |
| Propagation Delay | 35 ns |
| Turn On Delay Time | 42 ns |
| Logic Function | Demultiplexer, Multiplexer |
| Number of Inputs | 8 |
| Supply Type | Single |
| On-State Resistance (Max) | 195Ohm |
| Multiplexer/Demultiplexer Circuit | 4:1 |
| Number of Input Lines | 4 |
| Current - Leakage (IS(off)) (Max) | 100nA |
| Channel Capacitance (CS(off), CD(off)) | 10pF |
| On-state Resistance Match-Nom | 2Ohm |
| Switch Circuit | SP4T |
| Switch Time (Ton, Toff) (Max) | 39ns, 78ns |
| Channel-to-Channel Matching (ΔRon) | 3 Ω |
| Switch-on Time-Max | 57.5ns |
| Switch-off Time-Max | 115ns |
| Voltage - Supply, Single (V+) | 2V~6V |
| Drain to Source Resistance | 650Ohm |
| Height Seated (Max) | 1.1mm |
| Length | 5mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
74HC4852PW-Q100,11 Overview
The electronic component is convenient to ship overseas because it is packed in a 16-TSSOP (0.173, 4.40mm Width). A high level of reliability can be achieved through the use of an advanced packaging method Tape & Reel (TR). It is mounted in the position Surface Mount. Multiplexers and demultiplexers have a number of circuits 4:1. Increasing operating temperature to around -40°C~125°C TA. A total of 16 terminations have been recorded. Due to its 4 channels, the electrical component produces high-quality output. When a voltage supply of 3V is used, the electronic component should be turned on and run. An injection of 16 pins is performed into the body of the electrical component. These analog multiplexers are built based on SP4T switching circuits. A 2 circuit is present in this switch device. Use 74HC4852 to search for variants of the digital switches. The internal resistance of this digital multiplexer is 195Ohm. For functions related to 16 pins, please refer to the datasheets. Multiplexers should not be powered above 6V in normal situations. Analog switch ics with Single supply type are cost-effective. 2V is the lowest voltage the electrical component should receive. In order to operate this switch device, it would need a current of 2μA. The voltage required by this switch device is 2V~6V, draining from a single voltage supply. There are 8 inputs to be operated. Drain to Source resistance is 650Ohm. The series starts with Automotive, AEC-Q100.
74HC4852PW-Q100,11 Features
4 Channels
Switch Circuit: SP4T
2μA Supply Current
Drain-to-Source resistance: 650Ohm
74HC4852PW-Q100,11 Applications
There are a lot of Nexperia USA Inc. 74HC4852PW-Q100,11 Analog Switches & Multiplexers ICs applications.
- Relay replacements
- Battery-powered systems
- Communications systems
- Imaging
- Precision data acquisition
- ISDN NT1/TA
- Microwave transmission systems
- PBX interfaces
- Avionics and Military Systems
- Medical Instrumentation
