74HC540N
| Parameters | |
|---|---|
| Mount | Through Hole |
| Package / Case | DIP |
| Number of Pins | 20 |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Number of Terminations | 20 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Max Operating Temperature | 125°C |
| Min Operating Temperature | -40°C |
| Additional Feature | WITH DUAL OUTPUT ENABLE |
| Subcategory | Bus Driver/Transceivers |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 2.54mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Pin Count | 20 |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Inverting |
| Temperature Grade | AUTOMOTIVE |
| Max Supply Voltage | 6V |
| Min Supply Voltage | 2V |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Number of Bits | 8 |
| Propagation Delay | 240 ns |
| Quiescent Current | 8μA |
| Family | HC/UH |
| Logic Function | Buffer |
| Number of Inputs | 8 |
| Output Characteristics | 3-STATE |
| Logic IC Type | BUS DRIVER |
| Max I(ol) | 0.006 A |
| Prop. Delay@Nom-Sup | 30 ns |
| High Level Output Current | -7.8mA |
| Low Level Output Current | 7.8mA |
| Control Type | ENABLE LOW |
| Height Seated (Max) | 4.2mm |
| Length | 26.73mm |
| Width | 7.62mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
74HC540N Overview
It is packaged in an DIP-case that protects the operational amplifiers from damage. There have been a total of 20 terminations over the past year. The pins on this board total to 20 in total. Please take in mind that op amp should be run at 5V. A type of Bus Driver/Transceivers op amp ic can be identified by the fact that this is a type of Bus Driver/Transceivers device. 20 pins are available on the instrumentation amplifier. For this linear amplifier to work, the temperature should not be below -40°C. At temperatures greater than 125°C, Instrumentation amplifier should not be used. The buffer op amp is rated for an operating voltage of 1 when it comes to the power supply. The operating supply voltage of the buffer op amp is rated at 5V. The electrical part is capable of being powered by a voltage of under 6V, which means that it can be used with any voltage supply. It is recommended that you keep the instrumentation amplifier's supply voltage higher than 2V when using it. The quiescent current is 8μA. This buffer op amp has an additional benefit, which you can refer to as follows: WITH DUAL OUTPUT ENABLE. In addition to being popular among hobbyists and technicians alike, this 8-bit op amp ic is well suited for many other applications as well. 2 ports let the buffer op amp manage a variety of tasks.
74HC540N Features
20 Pins
supply voltage of 5V
74HC540N Applications
There are a lot of NXP Semiconductors / Freescale 74HC540N Instrumentational OP Amps applications.
- Inverse/same-phase proportional circuit
- Hand-held batteries
- Wireless base stations
- Test and measurement instruments
- Logarithmic operation circuits
- Signal operation
- Car stereo
- Subtraction operation circuits
- Navigation
- Micro signal measurement
