74HC574D-Q100,118
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 20 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74HC |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Technology | CMOS |
| Voltage - Supply | 2V~6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | 74HC574 |
| Function | Standard |
| Output Type | Tri-State, Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 6V |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Ports | 2 |
| Clock Frequency | 133MHz |
| Propagation Delay | 225 ns |
| Quiescent Current | 8μA |
| Turn On Delay Time | 14 ns |
| Family | HC/UH |
| Output Characteristics | 3-STATE |
| Current - Output High, Low | 7.8mA 7.8mA |
| Number of Bits per Element | 8 |
| Max Propagation Delay @ V, Max CL | 26ns @ 6V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 3.5pF |
| Clock Edge Trigger Type | Positive Edge |
| Height Seated (Max) | 2.65mm |
| Width | 7.5mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
74HC574D-Q100,118 Overview
As a result, it is packaged as 20-SOIC (0.295, 7.50mm Width). The package Tape & Reel (TR)contains it. There is a Tri-State, Non-Invertedoutput configured with it. In the configuration of the trigger, Positive Edgeis used. This electronic part is mounted in the way of Surface Mount. Powered by a 2V~6Vvolt supply, it operates as follows. The operating temperature is -40°C~125°C TA. Logic flip flops of this type are classified as D-Type. It belongs to the 74HCseries of FPGAs. You should not exceed 133MHzin the output frequency of the device. In total, it contains 1 elements. It has been determined that there have been 20 terminations. D latch belongs to the 74HC574 family. A voltage of 5V is used as the power supply for this D latch. The input capacitance of this T flip flop is 3.5pF farads, which is defined as the capacitance between the input terminals of an op amp with either input grounded. An electronic device belonging to the family HC/UHcan be found here. Electronic part Surface Mountis mounted in the way. With its 20pins, it is designed to work with most electronic flip flops. Its clock edge trigger type is Positive Edge. As soon as 6Vis reached, Vsup reaches its maximum value. Normal operation requires a supply voltage (Vsup) above 2V. The flip flop has 2ports embedded within it. If high efficiency is to be achieved, the supply voltage should be maintained at 5V. It consumes a total of 8μA quiescent current at any given time.
74HC574D-Q100,118 Features
Tape & Reel (TR) package
74HC series
20 pins
74HC574D-Q100,118 Applications
There are a lot of Nexperia USA Inc. 74HC574D-Q100,118 Flip Flops applications.
- Data storage
- Registers
- Computing
- Consumer
- Guaranteed simultaneous switching noise level
- Automotive
- Supports Live Insertion
- Count Modes
- Functionally equivalent to the MC10/100EL29
- Divide a clock signal by 2 or 4
