74HC574D,652
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.295, 7.50mm Width) |
| Surface Mount | YES |
| Number of Pins | 20 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tube |
| Series | 74HC |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Additional Feature | BROADSIDE VERSION OF 374 |
| Technology | CMOS |
| Voltage - Supply | 2V~6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | 74HC574 |
| Function | Standard |
| Qualification Status | Not Qualified |
| Output Type | Tri-State, Non-Inverted |
| Number of Elements | 1 |
| Supply Voltage-Max (Vsup) | 6V |
| Supply Voltage-Min (Vsup) | 2V |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Output Current | 7.8mA |
| Clock Frequency | 133MHz |
| Family | HC/UH |
| Current - Quiescent (Iq) | 8μA |
| Output Characteristics | 3-STATE |
| Current - Output High, Low | 7.8mA 7.8mA |
| Output Polarity | TRUE |
| Number of Bits per Element | 8 |
| Max Propagation Delay @ V, Max CL | 26ns @ 6V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 3.5pF |
| Propagation Delay (tpd) | 45 ns |
| Height Seated (Max) | 2.65mm |
| Width | 7.5mm |
| RoHS Status | ROHS3 Compliant |
74HC574D,652 Overview
The item is packaged in 20-SOIC (0.295, 7.50mm Width)cases. You can find it in the Tubepackage. Currently, the output is configured to use Tri-State, Non-Inverted. This trigger uses the value Positive Edge. Surface Mountis in the way of this electric part. The supply voltage is set to 2V~6V. A temperature of -40°C~125°C TAis considered to be the operating temperature. Logic flip flops of this type are classified as D-Type. In terms of FPGAs, it belongs to the 74HC series. A frequency of 133MHzshould be the maximum output frequency. There are 1 elements in it. As a result, it consumes 8μA of quiescent current without being affected by external factors. Currently, there are 20 terminations. It is a member of the 74HC574 family. The power source is powered by 5V. The input capacitance of this T flip flop is 3.5pF farads, which is defined as the capacitance between the input terminals of an op amp with either input grounded. The electronic device belongs to the HC/UHfamily. This board is designed with 20pins on it. 6Vis the maximum supply voltage (Vsup). Normally, the supply voltage (Vsup) should be above 2V. The D flip flop has no ports embedded. Featuring the maximum design flexibility, it has an output current of 7.8mA . BROADSIDE VERSION OF 374is also one of its characteristics.
74HC574D,652 Features
Tube package
74HC series
20 pins
74HC574D,652 Applications
There are a lot of Nexperia USA Inc. 74HC574D,652 Flip Flops applications.
- Memory
- EMI reduction circuitry
- Modulo – n – counter
- Communications
- Single Up Count-Control Line
- Power down protection
- Frequency division
- Latch-up performance
- Circuit Design
- Test & Measurement
