74HC574DTR2G
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 20 |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74HC |
| JESD-609 Code | e4 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Voltage - Supply | 2V~6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.65mm |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | 74HC574 |
| Function | Standard |
| Qualification Status | Not Qualified |
| Output Type | Tri-State, Non-Inverted |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 6V |
| Power Supplies | 2/6V |
| Supply Voltage-Min (Vsup) | 2V |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Output Current | 7.8mA |
| Number of Bits | 8 |
| Clock Frequency | 28MHz |
| Propagation Delay | 240 ns |
| Turn On Delay Time | 34 ns |
| Family | HC/UH |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 4μA |
| Output Characteristics | 3-STATE |
| Current - Output High, Low | 7.8mA 7.8mA |
| Max I(ol) | 0.006 A |
| Max Propagation Delay @ V, Max CL | 27ns @ 6V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 10pF |
| Number of Input Lines | 8 |
| Clock Edge Trigger Type | Positive Edge |
| Height | 1.0414mm |
| Length | 6.5786mm |
| Width | 4.4958mm |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
74HC574DTR2G Overview
The package is in the form of 20-TSSOP (0.173, 4.40mm Width). It is contained within the Tape & Reel (TR)package. Currently, the output is configured to use Tri-State, Non-Inverted. It is configured with a trigger that uses a value of Positive Edge. The electronic part is mounted in the way of Surface Mount. A voltage of 2V~6Vis required for its operation. Currently, the operating temperature is -55°C~125°C TA. There is D-Type type of electronic flip flop associated with this device. FPGAs belonging to the 74HCseries contain this type of chip. In order for it to function properly, its output frequency should not exceed 28MHz. In total, there are 1 elements. It consumes 4μA of quiescent current without being affected by external factors. A total of 20 terminations have been made. D latch belongs to the 74HC574 family. It is powered by a voltage of 3V . The input capacitance of this JK flip flopis 10pF farads. Devices in the HC/UHfamily are electronic devices. Electronic part Surface Mountis mounted in the way. This board has 20 pins. It has a clock edge trigger type of Positive Edge. This device is part of the FF/Latchesbase part number family. It is designed with a number of bits of 8. In this case, the maximum supply voltage (Vsup) reaches 6V. The supply voltage (Vsup) should be maintained above 2V for normal operation. A reliable performance of this D flip flop makes it well suited for use in TAPE AND REEL. There are 2/6V power supplies attached to it. The D flip flop has no ports embedded. Its output current of 7.8mAallows for maximum design flexibility. This input has 8lines in it.
74HC574DTR2G Features
Tape & Reel (TR) package
74HC series
20 pins
8 Bits
2/6V power supplies
74HC574DTR2G Applications
There are a lot of ON Semiconductor 74HC574DTR2G Flip Flops applications.
- Balanced 24 mA output drivers
- Asynchronous counter
- Counters
- Balanced Propagation Delays
- Memory
- Single Up Count-Control Line
- Divide a clock signal by 2 or 4
- Shift registers
- CMOS Process
- Synchronous counter
