74HC73PW,118
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 14 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74HC |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| Type | JK Type |
| Additional Feature | MASTER SLAVE OPERATION |
| Technology | CMOS |
| Voltage - Supply | 2V~6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | 74HC73 |
| Function | Reset |
| Output Type | Differential |
| Operating Supply Voltage | 5V |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 6V |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Circuits | 2 |
| Clock Frequency | 83MHz |
| Propagation Delay | 27 ns |
| Quiescent Current | 4μA |
| Turn On Delay Time | 15 ns |
| Family | HC/UH |
| Logic Function | Flip-Flop, JK-Type |
| Current - Output High, Low | 5.2mA 5.2mA |
| Number of Bits per Element | 1 |
| Max Propagation Delay @ V, Max CL | 27ns @ 6V, 50pF |
| Trigger Type | Negative Edge |
| Input Capacitance | 3.5pF |
| Clock Edge Trigger Type | Negative Edge |
| Length | 5mm |
| Width | 4.4mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
74HC73PW,118 Overview
The item is packaged in 14-TSSOP (0.173, 4.40mm Width)cases. It is included in the package Tape & Reel (TR). This output is configured with Differential. Negative Edgeis the trigger it is configured with. Surface Mountmounts this electrical part. The JK flip flop operates with an input voltage of 2V~6V volts. A temperature of -40°C~125°C TAis used in the operation. Logic flip flops of this type are classified as JK Type. JK flip flop belongs to the 74HCseries of FPGAs. There should be no greater frequency than 83MHzon its output. The number of terminations is 14. You can search similar parts based on 74HC73. An input voltage of 5Vpowers the D latch. A 3.5pFfarad input capacitance is provided by this T flip flop. An electronic device belonging to the family HC/UHcan be found here. The electronic part is mounted in the way of Surface Mount. Basically, it is designed with a set of 14 pins. This device has Negative Edgeas its clock edge trigger type. Vsup reaches its maximum value at 6V. Normally, the supply voltage (Vsup) should be kept above 2V. In order to achieve its superior flexibility, 2 circuits are used. For high efficiency, the supply voltage should be kept at 5V. It consumes 4μA of quiescent current without being affected by external factors. As an additional reference, you may refer to electronic flip flop MASTER SLAVE OPERATION.
74HC73PW,118 Features
Tape & Reel (TR) package
74HC series
14 pins
74HC73PW,118 Applications
There are a lot of Nexperia USA Inc. 74HC73PW,118 Flip Flops applications.
- Power down protection
- Reduced system switching noise
- Consumer
- ESCC
- Synchronous counter
- ESD protection
- Asynchronous counter
- Frequency Dividers
- Test & Measurement
- Automotive
