74HCT109D,653
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Supplier Device Package | 16-SO |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2013 |
| Series | 74HCT |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Type | JK Type |
| Max Operating Temperature | 125°C |
| Min Operating Temperature | -40°C |
| Voltage - Supply | 4.5V~5.5V |
| Frequency | 55MHz |
| Base Part Number | 74HCT109 |
| Function | Set(Preset) and Reset |
| Output Type | Differential |
| Operating Supply Voltage | 5V |
| Number of Elements | 2 |
| Polarity | Non-Inverting |
| Number of Circuits | 2 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Number of Bits | 2 |
| Clock Frequency | 55MHz |
| Propagation Delay | 17 ns |
| Turn On Delay Time | 13 ns |
| Logic Function | AND, Flip-Flop, JK-Type |
| Current - Quiescent (Iq) | 4μA |
| Current - Output High, Low | 4mA 4mA |
| Number of Bits per Element | 1 |
| Max Propagation Delay @ V, Max CL | 35ns @ 4.5V, 50pF |
| Trigger Type | Positive Edge |
| High Level Output Current | -4mA |
| Input Capacitance | 3.5pF |
| Low Level Output Current | 4mA |
| Number of Input Lines | 2 |
| Number of Output Lines | 1 |
| Clock Edge Trigger Type | Positive Edge |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
74HCT109D,653 Overview
16-SOIC (0.154, 3.90mm Width)is the packaging method. The package Tape & Reel (TR)contains it. T flip flop uses Differentialas its output configuration. It is configured with the trigger Positive Edge. It is mounted in the way of Surface Mount. With a supply voltage of 4.5V~5.5V volts, it operates. A temperature of -40°C~125°C TAis used in the operation. This D latch has the type JK Type. In this case, it is a type of FPGA belonging to the 74HCT series. You should not exceed 55MHzin the output frequency of the device. D latch consists of 2 elements. During its operation, it consumes 4μA quiescent energy. If you search by 74HCT109, you will find similar parts. JK flip flop input capacitance is 3.5pF farads. This electronic part is mounted in the way of Surface Mount. There are 16pins on it. Edge triggering is a type of triggering that allows a circuit to become active at the positive edge or the negative edge of the clock signal. The clock edge trigger type of this device is Positive Edge. An electronic part designed with 2bits is used in this application. Despite its superior flexibility, it relies on 2 circuits to achieve it. In order to ensure high efficiency, the supply voltage should remain at 5V. To operate, the chip has a total of 1 output lines. Currently, there are 2 lines of input. A -4mAis set for the high level output current. The low level output current is set to 4mA. It is recommended that the operating temperature be lower than 125°C. In order for the system to operate properly, the temperature should be higher than -40°C. A minimum supply voltage of 4.5V is required for these RS flip flops to operate. The maximum supply voltage supported by the flip flop is 5.5V. A frequency of 55MHzcan be achieved.
74HCT109D,653 Features
Tape & Reel (TR) package
74HCT series
16 pins
2 Bits
74HCT109D,653 Applications
There are a lot of Nexperia USA Inc. 74HCT109D,653 Flip Flops applications.
- Circuit Design
- Memory
- Load Control
- Buffer registers
- Frequency Dividers
- Data storage
- Balanced 24 mA output drivers
- Individual Asynchronous Resets
- ESD protection
- Guaranteed simultaneous switching noise level
