74HCT112PW,118
| Parameters | |
|---|---|
| Number of Pins | 16 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2013 |
| Series | 74HCT |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Type | JK Type |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | 74HCT112 |
| Function | Set(Preset) and Reset |
| Output Type | Differential |
| Operating Supply Voltage | 5V |
| Polarity | Non-Inverting |
| Number of Circuits | 2 |
| Load Capacitance | 50pF |
| Clock Frequency | 64MHz |
| Propagation Delay | 19 ns |
| Quiescent Current | 4μA |
| Turn On Delay Time | 21 ns |
| Family | HCT |
| Logic Function | AND, Flip-Flop, JK-Type |
| Current - Output High, Low | 4mA 4mA |
| Number of Bits per Element | 1 |
| Max Propagation Delay @ V, Max CL | 35ns @ 4.5V, 50pF |
| Trigger Type | Negative Edge |
| Input Capacitance | 3.5pF |
| Clock Edge Trigger Type | Negative Edge |
| Length | 5mm |
| Width | 4.4mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Factory Lead Time | 1 Week |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
74HCT112PW,118 Overview
It is embeded in 16-TSSOP (0.173, 4.40mm Width) case. D flip flop is included in the Tape & Reel (TR)package. It is configured with Differentialas an output. This trigger uses the value Negative Edge. In this case, the electronic component is mounted in the way of Surface Mount. The JK flip flop operates with an input voltage of 4.5V~5.5V volts. Currently, the operating temperature is -40°C~125°C TA. This electronic flip flop is of type JK Type. JK flip flop belongs to the 74HCTseries of FPGAs. A frequency of 64MHzshould not be exceeded by its output. Terminations are 16. If you search by 74HCT112, you will find similar parts. A voltage of 5V provides power to the D latch. There is 3.5pF input capacitance for this T flip flop. In this case, the D flip flop belongs to the HCTfamily. There is an electronic component mounted in the way of Surface Mount. 16pins are included in its design. This device has Negative Edgeas its clock edge trigger type. Using 2 circuits, it is highly flexible. If high efficiency is to be achieved, the supply voltage should be maintained at 5V. Quiescent current is consumed by the D latch in the amount of 4μA.
74HCT112PW,118 Features
Tape & Reel (TR) package
74HCT series
16 pins
74HCT112PW,118 Applications
There are a lot of Nexperia USA Inc. 74HCT112PW,118 Flip Flops applications.
- Dynamic threshold performance
- Balanced 24 mA output drivers
- Circuit Design
- Test & Measurement
- Safety Clamp
- ATE
- Instrumentation
- Data transfer
- Patented noise
- Shift Registers
