74HCT174DB,112
| Parameters | |
|---|---|
| Width | 5.3mm |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
| Factory Lead Time | 1 Week |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SSOP (0.209, 5.30mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tube |
| Published | 2013 |
| Series | 74HCT |
| JESD-609 Code | e4 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Type | D-Type |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | 74HCT174 |
| Function | Master Reset |
| Output Type | Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Load Capacitance | 50pF |
| Number of Bits | 6 |
| Clock Frequency | 69MHz |
| Propagation Delay | 18 ns |
| Quiescent Current | 8μA |
| Turn On Delay Time | 21 ns |
| Family | HCT |
| Logic Function | D-Type, Flip-Flop |
| Current - Output High, Low | 4mA 5.2mA |
| Max Propagation Delay @ V, Max CL | 35ns @ 4.5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 3.5pF |
| Number of Input Lines | 6 |
| fmax-Min | 20 MHz |
| Clock Edge Trigger Type | Positive Edge |
| Height Seated (Max) | 2mm |
74HCT174DB,112 Overview
The flip flop is packaged in a case of 16-SSOP (0.209, 5.30mm Width). The package Tubecontains it. It is configured with Non-Invertedas an output. It is configured with a trigger that uses a value of Positive Edge. It is mounted in the way of Surface Mount. The supply voltage is set to 4.5V~5.5V. The operating temperature is -40°C~125°C TA. D-Typedescribes this flip flop. JK flip flop belongs to the 74HCTseries of FPGAs. A frequency of 69MHzshould be the maximum output frequency. The list contains 1 elements. In 16terminations, a transmission line is terminated with a JK flip flop that matches its characteristic impedance. It is a member of the 74HCT174 family. The power source is powered by 5V. Its input capacitance is 3.5pF farads. In terms of electronic devices, this device belongs to the HCTfamily of devices. This electronic part is mounted in the way of Surface Mount. This board is designed with 16pins on it. This device has the clock edge trigger type of Positive Edge. Flip flops designed with 6bits are used in this part. A high level of efficiency can be achieved by maintaining the supply voltage at 5V. It has 6lines. Quiescent current is consumed by the D latch in the amount of 8μA.
74HCT174DB,112 Features
Tube package
74HCT series
16 pins
6 Bits
74HCT174DB,112 Applications
There are a lot of Nexperia USA Inc. 74HCT174DB,112 Flip Flops applications.
- Convert a momentary switch to a toggle switch
- ATE
- Single Up Count-Control Line
- 2 – Bit synchronous counter
- Consumer
- Event Detectors
- ESCC
- Power down protection
- Latch
- Buffer registers
