74HCT174DB,118
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SSOP (0.209, 5.30mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2013 |
| Series | 74HCT |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Type | D-Type |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | 74HCT174 |
| Function | Master Reset |
| Output Type | Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Number of Channels | 6 |
| Load Capacitance | 50pF |
| Number of Bits | 6 |
| Clock Frequency | 69MHz |
| Propagation Delay | 18 ns |
| Quiescent Current | 8μA |
| Turn On Delay Time | 21 ns |
| Family | HCT |
| Logic Function | D-Type, Flip-Flop |
| Current - Output High, Low | 4mA 5.2mA |
| Max Propagation Delay @ V, Max CL | 35ns @ 4.5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 3.5pF |
| fmax-Min | 20 MHz |
| Clock Edge Trigger Type | Positive Edge |
| Height Seated (Max) | 2mm |
| Width | 5.3mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
74HCT174DB,118 Overview
As a result, it is packaged as 16-SSOP (0.209, 5.30mm Width). The Tape & Reel (TR)package contains it. T flip flop is configured with an output of Non-Inverted. The trigger it is configured with uses Positive Edge. Surface Mountis occupied by this electronic component. Powered by a 4.5V~5.5Vvolt supply, it operates as follows. It is operating at -40°C~125°C TA. It is an electronic flip flop with the type D-Type. In FPGA terms, D flip flop is a type of 74HCTseries FPGA. In order for it to function properly, its output frequency should not exceed 69MHz. A total of 1elements are present in it. There are 16 terminations, which are the practice of ending a transmission line with a device that matches the characteristic impedance of the line. If you search by 74HCT174, you will find similar parts. It is powered by a voltage of 5V . There is 3.5pF input capacitance for this T flip flop. This D flip flop belongs to the family of HCT. There is an electronic part mounted in the way of Surface Mount. As you can see from the design, it has pins with 16. A Positive Edgeclock edge trigger is used in this device. An electronic part with 6bits has been designed. If high efficiency is desired, the supply voltage should be kept at 5V. Despite external influences, it consumes 8μAof quiescent current. The number of channels is growing strong/weak: 6.
74HCT174DB,118 Features
Tape & Reel (TR) package
74HCT series
16 pins
6 Bits
74HCT174DB,118 Applications
There are a lot of Nexperia USA Inc. 74HCT174DB,118 Flip Flops applications.
- Computers
- Load Control
- Communications
- ESD protection
- Functionally equivalent to the MC10/100EL29
- Single Up Count-Control Line
- Pattern generators
- Guaranteed simultaneous switching noise level
- Instrumentation
- Divide a clock signal by 2 or 4
