74HCT175PW,112
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tube |
| Published | 2011 |
| Series | 74HCT |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | 74HCT175 |
| Function | Master Reset |
| Output Type | Differential |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Number of Bits | 4 |
| Clock Frequency | 49MHz |
| Propagation Delay | 16 ns |
| Turn On Delay Time | 19 ns |
| Family | HCT |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 8μA |
| Current - Output High, Low | 4mA 4mA |
| Max Propagation Delay @ V, Max CL | 33ns @ 4.5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 3.5pF |
| Number of Input Lines | 4 |
| Clock Edge Trigger Type | Positive Edge |
| Length | 5mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
74HCT175PW,112 Overview
It is packaged in the way of 16-TSSOP (0.173, 4.40mm Width). The package Tubecontains it. It is configured with Differentialas an output. In the configuration of the trigger, Positive Edgeis used. Surface Mountis occupied by this electronic component. Powered by a 4.5V~5.5Vvolt supply, it operates as follows. Currently, the operating temperature is -40°C~125°C TA. Logic flip flops of this type are classified as D-Type. JK flip flop is a part of the 74HCTseries of FPGAs. You should not exceed 49MHzin the output frequency of the device. The element count is 1 . There is 8μA quiescent consumption. There are 16 terminations,It is a member of the 74HCT175 family. It is powered from a supply voltage of 5V. The input capacitance of this T flip flop is 3.5pF farads, which is defined as the capacitance between the input terminals of an op amp with either input grounded. It is a member of the HCTfamily of D flip flop. The electronic part is mounted in the way of Surface Mount. The 16pins are designed into the board. This device's clock edge trigger type is Positive Edge. 4bits are used in its design. The supply voltage should be maintained at 5V for high efficiency. The number of input lines is 4.
74HCT175PW,112 Features
Tube package
74HCT series
16 pins
4 Bits
74HCT175PW,112 Applications
There are a lot of Nexperia USA Inc. 74HCT175PW,112 Flip Flops applications.
- Data Synchronizers
- Data storage
- Instrumentation
- Power down protection
- EMI reduction circuitry
- Frequency division
- Count Modes
- Single Up Count-Control Line
- Balanced 24 mA output drivers
- Shift registers
