74HCT1G66GV-Q100H
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SC-74A, SOT-753 |
| Number of Pins | 5 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2008 |
| Series | Automotive, AEC-Q100 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| Resistance | 128Ohm |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Base Part Number | 74HCT1G66 |
| Pin Count | 5 |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Max Supply Voltage | 10V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 20μA |
| Throw Configuration | SPST |
| Supply Type | Single |
| -3db Bandwidth | 200MHz |
| On-State Resistance (Max) | 95Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 50 dB |
| Current - Leakage (IS(off)) (Max) | 1μA |
| Channel Capacitance (CS(off), CD(off)) | 1.5pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 30ns, 44ns |
| Voltage - Supply, Single (V+) | 4.5V~5.5V |
| Length | 2.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
74HCT1G66GV-Q100H Overview
The electronic part can be shipped overseas conveniently because it is packaged in SC-74A, SOT-753. This high-reliability packaging method uses advanced packaging methods Tape & Reel (TR). In Surface Mount, this analog switch is mounted. Multiplexer and demultiplexer circuits have a number 1:1. The operating temperature is extended to around -40°C~125°C TA. In total, there are 5 terminations. A high-quality output is provided by the electrical component's 1 channels. If the voltage supply is 5V volts, the electrical component should be turned on and run. There are 5 pins injected into the electronic part body. A SPST - NO switching circuit is used to build these analog multiplexers. The circuits in this analogue multiplexer number 1. Use 74HCT1G66 to search for variants of the digital switches. The internal resistance of this digital multiplexer is 128Ohm. The functions of 5 pins can be found in the datasheets. Multiplexers should not be powered above 10V in normal situations. Analog switch ics with Single supply type are cost-effective. 2V should be the lowest voltage fed to the electronic component. The analogue multiplexer could operate on 20μA current. Analogue multiplexers require a 4.5V~5.5V voltage to drain from a single voltage supply. This is electronic component of the Automotive, AEC-Q100 series.
74HCT1G66GV-Q100H Features
1 Channels
Switch Circuit: SPST - NO
20μA Supply Current
-3db Bandwidth: 200MHz
74HCT1G66GV-Q100H Applications
There are a lot of Nexperia USA Inc. 74HCT1G66GV-Q100H Analog Switches & Multiplexers ICs applications.
- Digital access cross connects
- ISDN NT1/TA
- DSUs
- T1/E1 Terminals
- Wireless Local Loop
- Residential Gateways, Home Gateway/Router
- Audio signal routing
- Digital Cross-Connects
- Industrial control systems
- Isolation
