74HCT1G66GW,125
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 5-TSSOP, SC-70-5, SOT-353 |
| Number of Pins | 5 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2008 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| Resistance | 15Ohm |
| Terminal Finish | Tin (Sn) |
| Max Power Dissipation | 250mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | 74HCT1G66 |
| Pin Count | 5 |
| Operating Supply Voltage | 5V |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Operating Supply Current | 200μA |
| Nominal Supply Current | 50mA |
| Power Dissipation | 250mW |
| Max Supply Current | 50mA |
| Throw Configuration | SPST |
| Turn On Delay Time | 15 ns |
| Number of Inputs | 1 |
| Supply Type | Single |
| Turn-Off Delay Time | 13 ns |
| -3db Bandwidth | 200MHz |
| On-State Resistance (Max) | 95Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 50 dB |
| Current - Leakage (IS(off)) (Max) | 1μA |
| Channel Capacitance (CS(off), CD(off)) | 1.5pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 30ns, 44ns |
| Switch-on Time-Max | 36ns |
| Voltage - Supply, Single (V+) | 4.5V~5.5V |
| Length | 2mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
74HCT1G66GW,125 Overview
The electrical component comes in 5-TSSOP, SC-70-5, SOT-353 packaging, which makes it convenient to ship overseas. A high level of reliability can be achieved through the use of an advanced packaging method Tape & Reel (TR). Surface Mount is where this multiplexer is located. Multiplexer and demultiplexer circuits have a number 1:1. Increasing operating temperature to around -40°C~125°C TA. A total of 5 terminations have been recorded. A 1 channel electronic part produces high-quality output. Turning on and running the electrical part should be easy with a 5V voltage supply. It is injected into the electrical part body with 5 pins. Based on SPST - NO switching circuits, these analog multiplexers work. Using the 74HCT1G66 search parameter, you can discover variants of the switch. It has an internal resistance of 15Ohm. For details about the functions of 5 pins, please refer to the datasheets. In a normalsituation, users should not supply the switches with voltage higher than 5.5V. Analogue multiplexer with a Single supply type that is cost-effective. The lowest voltage fed to the electronic component should be 4.5V. An operating current of 200μA would be sufficient for this switch device. An analogue multiplexer drains from a single voltage supply at 4.5V~5.5V. The switch multiplexer may be damaged if it is exposed to voltage greater than 50mA. A voltage of 5V can be used to operate the electronic component. The electrical component supports 1 inputs.
74HCT1G66GW,125 Features
1 Channels
Switch Circuit: SPST - NO
200μA Supply Current
-3db Bandwidth: 200MHz
74HCT1G66GW,125 Applications
There are a lot of Nexperia USA Inc. 74HCT1G66GW,125 Analog Switches & Multiplexers ICs applications.
- SONET
- Remote wireless modules
- Fault Tolerant Systems
- Communications systems
- Audio and video routing
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- FTTH
- E1 Network Equipment
- Digital cross connects (DSX-1)
- Industrial control systems
