74HCT1G66GW,165
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 5-TSSOP, SC-70-5, SOT-353 |
| Number of Pins | 5 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2008 |
| JESD-609 Code | e3 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Resistance | 128Ohm |
| Terminal Finish | Tin (Sn) |
| Max Power Dissipation | 250mW |
| Peak Reflow Temperature (Cel) | 260 |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | 74HCT1G66 |
| Pin Count | 5 |
| Operating Supply Voltage | 5V |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Operating Supply Current | 20μA |
| Nominal Supply Current | 50mA |
| Power Dissipation | 250mW |
| Max Supply Current | 50mA |
| Throw Configuration | SPST |
| Turn On Delay Time | 15 ns |
| Number of Inputs | 1 |
| Supply Type | Single |
| Turn-Off Delay Time | 13 ns |
| -3db Bandwidth | 200MHz |
| On-State Resistance (Max) | 95Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Current - Leakage (IS(off)) (Max) | 1μA |
| Channel Capacitance (CS(off), CD(off)) | 1.5pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 30ns, 44ns |
| Voltage - Supply, Single (V+) | 4.5V~5.5V |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
74HCT1G66GW,165 Overview
As the electronic part is packed in 5-TSSOP, SC-70-5, SOT-353, international shipping is convenient. In order to provide high reliability, an advanced packaging method Tape & Reel (TR) is used. There is an analog multiplexer mounted in position Surface Mount. Multiplexer and demultiplexer circuits have a number 1:1. Around -40°C~125°C TA is the extended operating temperature. The electrical component body receives 5 pins. A SPST - NO switching circuit is used to build these analog multiplexers. Try searching for the analog switch ic with 74HCT1G66 if you are looking for variants. An switch multiplexer with 128Ohm internal resistance has a value of 128Ohm. For functions related to 5 pins, please refer to the datasheets. It is normally recommended that users do not supply the multiplexer with voltages higher than 5.5V. A cost-effective Single supply type analogue multiplexer. In order for the electronic part to function properly, the lowest voltage should be 4.5V. For this digital switch to work, 20μA current would suffice. The voltage required by this switch device is 4.5V~5.5V, draining from a single voltage supply. If you put voltage higher than 50mA on the digital multiplexer, damage may occur. The electronic component can function from 5V. The electrical component supports 1 inputs.
74HCT1G66GW,165 Features
Switch Circuit: SPST - NO
20μA Supply Current
-3db Bandwidth: 200MHz
74HCT1G66GW,165 Applications
There are a lot of Nexperia USA Inc. 74HCT1G66GW,165 Analog Switches & Multiplexers ICs applications.
- Private Branch Exchange (PBX)
- Sample hold systems
- USB 1.1 signal switching circuits
- RGB switches
- Precision data acquisition
- Remote Powered Equipment
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Sample-and-hold systems
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- PDAs
