74HCT273BQ-Q100X
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-VFQFN Exposed Pad |
| Number of Pins | 20 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2001 |
| Series | 74HCT |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Type | D-Type |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | QUAD |
| Terminal Form | NO LEAD |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Supply Voltage | 5V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | 74HCT273 |
| Function | Master Reset |
| Output Type | Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Number of Bits | 8 |
| Clock Frequency | 36MHz |
| Propagation Delay | 30 ns |
| Quiescent Current | 8μA |
| Turn On Delay Time | 30 ns |
| Family | HCT |
| Logic Function | D-Type, Flip-Flop |
| Current - Output High, Low | 4mA 5.2mA |
| Max Propagation Delay @ V, Max CL | 30ns @ 4.5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 3.5pF |
| Number of Input Lines | 8 |
| Clock Edge Trigger Type | Positive Edge |
| Length | 4.5mm |
| Width | 2.5mm |
| RoHS Status | ROHS3 Compliant |
74HCT273BQ-Q100X Overview
20-VFQFN Exposed Padis the way it is packaged. As part of the package Tape & Reel (TR), it is embedded. T flip flop uses Non-Invertedas its output configuration. There is a trigger configured with Positive Edge. There is an electrical part that is mounted in the way of Surface Mount. The JK flip flop operates at a voltage of 4.5V~5.5V. Currently, the operating temperature is -40°C~125°C TA. This D latch has the type D-Type. FPGAs belonging to the 74HCTseries contain this type of chip. Its output frequency should not exceed 36MHz Hz. In total, it contains 1 elements. 20terminations have occurred. Members of the 74HCT273family make up this object. It is powered by a voltage of 5V . The input capacitance of this T flip flop is 3.5pF farads, which is defined as the capacitance between the input terminals of an op amp with either input grounded. This D flip flop belongs to the family of HCT. There is an electronic component mounted in the way of Surface Mount. As you can see from the design, it has pins with 20. This device's clock edge trigger type is Positive Edge. There are 8bits in its design. For high efficiency, the supply voltage should be kept at 5V. Currently, there are 8 input lines present. This D latch consumes 8μA quiescent current at all.
74HCT273BQ-Q100X Features
Tape & Reel (TR) package
74HCT series
20 pins
8 Bits
74HCT273BQ-Q100X Applications
There are a lot of Nexperia USA Inc. 74HCT273BQ-Q100X Flip Flops applications.
- Latch-up performance
- Pattern generators
- Cold spare funcion
- Divide a clock signal by 2 or 4
- Storage registers
- Bus hold
- Bounce elimination switch
- Buffer registers
- Count Modes
- ATE
