74HCT273D-Q100J
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 20 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 1997 |
| Series | 74HCT |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Type | D-Type |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | 74HCT273 |
| Function | Master Reset |
| Output Type | Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Number of Bits | 8 |
| Clock Frequency | 36MHz |
| Propagation Delay | 30 ns |
| Quiescent Current | 8μA |
| Turn On Delay Time | 15 ns |
| Family | HCT |
| Logic Function | D-Type, Flip-Flop |
| Current - Output High, Low | 4mA 5.2mA |
| Max Propagation Delay @ V, Max CL | 30ns @ 4.5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 3.5pF |
| Number of Input Lines | 8 |
| Clock Edge Trigger Type | Positive Edge |
| Height Seated (Max) | 2.65mm |
| Width | 7.5mm |
| RoHS Status | ROHS3 Compliant |
74HCT273D-Q100J Overview
It is embeded in 20-SOIC (0.295, 7.50mm Width) case. D flip flop is embedded in the Tape & Reel (TR) package. T flip flop is configured with an output of Non-Inverted. The trigger it is configured with uses Positive Edge. The electronic part is mounted in the way of Surface Mount. It operates with a supply voltage of 4.5V~5.5V. Temperature is set to -40°C~125°C TA. This logic flip flop is classified as type D-Type. JK flip flop is a part of the 74HCTseries of FPGAs. Its output frequency should not exceed 36MHz Hz. In total, there are 1 elements. A total of 20 terminations have been made. JK flip flop belongs to 74HCT273 family. It is powered by a voltage of 5V . This T flip flop has a capacitance of 3.5pF farads at the input. In terms of electronic devices, this device belongs to the HCTfamily of devices. There is an electronic component mounted in the way of Surface Mount. This board has 20 pins. It has a clock edge trigger type of Positive Edge. 8bits are used in its design. If high efficiency is to be achieved, the supply voltage should be maintained at 5V. This input has 8lines in it. Despite external influences, it consumes 8μAof quiescent current.
74HCT273D-Q100J Features
Tape & Reel (TR) package
74HCT series
20 pins
8 Bits
74HCT273D-Q100J Applications
There are a lot of Nexperia USA Inc. 74HCT273D-Q100J Flip Flops applications.
- Modulo – n – counter
- Parallel data storage
- Bounce elimination switch
- Patented noise
- Single Down Count-Control Line
- EMI reduction circuitry
- Registers
- Computing
- Counters
- ESD protection
