74HCT273D,653
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Gold, Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 20 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 1997 |
| Series | 74HCT |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | 74HCT273 |
| Function | Master Reset |
| Output Type | Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Load Capacitance | 50pF |
| Output Current | 25mA |
| Number of Bits | 8 |
| Clock Frequency | 36MHz |
| Propagation Delay | 15 ns |
| Quiescent Current | 8μA |
| Turn On Delay Time | 15 ns |
| Family | HCT |
| Logic Function | D-Type, Flip-Flop |
| Current - Output High, Low | 4mA 5.2mA |
| Max Propagation Delay @ V, Max CL | 30ns @ 4.5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 3.5pF |
| Number of Input Lines | 8 |
| Clock Edge Trigger Type | Positive Edge |
| Height Seated (Max) | 2.65mm |
| Width | 7.5mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
74HCT273D,653 Overview
The flip flop is packaged in a case of 20-SOIC (0.295, 7.50mm Width). There is an embedded version in the package Tape & Reel (TR). T flip flop is configured with an output of Non-Inverted. It is configured with a trigger that uses a value of Positive Edge. There is an electronic component mounted in the way of Surface Mount. Powered by a 4.5V~5.5Vvolt supply, it operates as follows. The operating temperature is -40°C~125°C TA. A flip flop of this type is classified as a D-Type. The 74HCTseries comprises this type of FPGA. In order for it to function properly, its output frequency should not exceed 36MHz. A total of 1elements are present in it. 20terminations have occurred. If you search by 74HCT273, you will find similar parts. It is powered by a voltage of 5V . A JK flip flop with a 3.5pFfarad input capacitance is used here. It is a member of the HCTfamily of D flip flop. In this case, the electronic component is mounted in the way of Surface Mount. This board is designed with 20pins on it. There is a clock edge trigger type of Positive Edgeon this device. An electronic part designed with 8bits is used in this application. If high efficiency is desired, the supply voltage should be kept at 5V. In addition to its maximum design flexibility, the output current of the T flip flop is 25mA. This input has 8lines. Quiescent current is consumed by the D latch in the amount of 8μA.
74HCT273D,653 Features
Tape & Reel (TR) package
74HCT series
20 pins
8 Bits
74HCT273D,653 Applications
There are a lot of Nexperia USA Inc. 74HCT273D,653 Flip Flops applications.
- Storage registers
- Computing
- Automotive
- Set-reset capability
- Parallel data storage
- Pattern generators
- ATE
- Buffer registers
- 2 – Bit synchronous counter
- Bus hold
