74HCT377D-Q100J
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 20 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2013 |
| Series | 74HCT |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Type | D-Type |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | 74HCT377 |
| Function | Standard |
| Output Type | Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Number of Bits | 8 |
| Clock Frequency | 53MHz |
| Propagation Delay | 32 ns |
| Quiescent Current | 8μA |
| Family | HCT |
| Logic Function | D-Type, Flip-Flop |
| Current - Output High, Low | 4mA 5.2mA |
| Max Propagation Delay @ V, Max CL | 32ns @ 4.5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 3.5pF |
| Number of Input Lines | 8 |
| Clock Edge Trigger Type | Positive Edge |
| Height Seated (Max) | 2.65mm |
| Width | 7.5mm |
| RoHS Status | ROHS3 Compliant |
74HCT377D-Q100J Overview
It is embeded in 20-SOIC (0.295, 7.50mm Width) case. Package Tape & Reel (TR)embeds it. There is a Non-Invertedoutput configured with it. In the configuration of the trigger, Positive Edgeis used. There is an electric part mounted in the way of Surface Mount. A voltage of 4.5V~5.5Vis required for its operation. It is operating at a temperature of -40°C~125°C TA. It is an electronic flip flop with the type D-Type. In FPGA terms, D flip flop is a type of 74HCTseries FPGA. This D flip flop should not have a frequency greater than 53MHz. The list contains 1 elements. Terminations are 20. You can search similar parts based on 74HCT377. The power source is powered by 5V. There is 3.5pF input capacitance for this T flip flop. Electronic devices of this type belong to the HCTfamily. Surface Mount mounts this electronic component. There are 20pins on it. In this device, the clock edge trigger type is Positive Edge. There are 8bits in this flip flop. If high efficiency is to be achieved, the supply voltage should be maintained at 5V. Currently, there are 8 lines of input. This D latch consumes 8μA quiescent current at all.
74HCT377D-Q100J Features
Tape & Reel (TR) package
74HCT series
20 pins
8 Bits
74HCT377D-Q100J Applications
There are a lot of Nexperia USA Inc. 74HCT377D-Q100J Flip Flops applications.
- Bounce elimination switch
- Convert a momentary switch to a toggle switch
- Digital electronics systems
- Power down protection
- Instrumentation
- 2 – Bit synchronous counter
- ESD protection
- EMI reduction circuitry
- Safety Clamp
- Frequency Divider circuits
