74HCT377D,652
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 20 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tube |
| Published | 2013 |
| Series | 74HCT |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Type | D-Type |
| Additional Feature | WITH HOLD MODE |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | 74HCT377 |
| Function | Standard |
| Output Type | Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Number of Bits | 8 |
| Clock Frequency | 53MHz |
| Propagation Delay | 14 ns |
| Quiescent Current | 8μA |
| Turn On Delay Time | 17 ns |
| Family | HCT |
| Logic Function | D-Type, Flip-Flop |
| Current - Output High, Low | 4mA 5.2mA |
| Max Propagation Delay @ V, Max CL | 32ns @ 4.5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 3.5pF |
| Number of Input Lines | 8 |
| Clock Edge Trigger Type | Positive Edge |
| Height Seated (Max) | 2.65mm |
| Width | 7.5mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
74HCT377D,652 Overview
It is embeded in 20-SOIC (0.295, 7.50mm Width) case. A package named Tubeincludes it. In the configuration, Non-Invertedis used as the output. The trigger it is configured with uses Positive Edge. There is an electronic component mounted in the way of Surface Mount. The JK flip flop operates at a voltage of 4.5V~5.5V. -40°C~125°C TAis the operating temperature. It is an electronic flip flop with the type D-Type. JK flip flop belongs to the 74HCTseries of FPGAs. A frequency of 53MHzshould be the maximum output frequency. D latch consists of 1 elements. A total of 20terminations have been recorded. Members of the 74HCT377family make up this object. The power supply voltage is 5V. The input capacitance of this T flip flop is 3.5pF farads, which is defined as the capacitance between the input terminals of an op amp with either input grounded. HCTis the family of this D flip flop. There is an electronic part that is mounted in the way of Surface Mount. There are 20pins on it. A Positive Edgeclock edge trigger is used in this device. It is designed with a number of bits of 8. For high efficiency, the supply voltage should be kept at 5V. Currently, there are 8 input lines present. It consumes 8μA current. Additionally, you may refer to the additional WITH HOLD MODE of the electronic flip flop.
74HCT377D,652 Features
Tube package
74HCT series
20 pins
8 Bits
74HCT377D,652 Applications
There are a lot of Nexperia USA Inc. 74HCT377D,652 Flip Flops applications.
- ATE
- 2 – Bit synchronous counter
- Dynamic threshold performance
- Consumer
- Counters
- Bus hold
- Safety Clamp
- Memory
- Frequency Dividers
- Bounce elimination switch
