74HCT377PW-Q100J
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 20 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2010 |
| Series | 74HCT |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Type | D-Type |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | 74HCT377 |
| Function | Standard |
| Output Type | Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Number of Bits | 8 |
| Clock Frequency | 53MHz |
| Propagation Delay | 32 ns |
| Quiescent Current | 8μA |
| Turn On Delay Time | 13 ns |
| Family | HCT |
| Logic Function | D-Type, Flip-Flop |
| Current - Output High, Low | 4mA 5.2mA |
| Max Propagation Delay @ V, Max CL | 32ns @ 4.5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 3.5pF |
| Number of Input Lines | 8 |
| Clock Edge Trigger Type | Positive Edge |
| Length | 6.5mm |
| Width | 4.4mm |
| RoHS Status | ROHS3 Compliant |
74HCT377PW-Q100J Overview
20-TSSOP (0.173, 4.40mm Width)is the packaging method. As part of the package Tape & Reel (TR), it is embedded. T flip flop uses Non-Invertedas the output. It is configured with a trigger that uses a value of Positive Edge. This electronic part is mounted in the way of Surface Mount. The JK flip flop operates with an input voltage of 4.5V~5.5V volts. It is operating at a temperature of -40°C~125°C TA. This logic flip flop is classified as type D-Type. This type of FPGA is a part of the 74HCT series. There should be no greater frequency than 53MHzon its output. In total, it contains 1 elements. In 20terminations, a transmission line is terminated with a JK flip flop that matches its characteristic impedance. It is a member of the 74HCT377 family. The D flip flop is powered by a voltage of 5V . This JK flip flop has a 3.5pFfarad input capacitance. Electronic devices of this type belong to the HCTfamily. It is mounted in the way of Surface Mount. It is designed with 20 pins. In this device, the clock edge trigger type is Positive Edge. It is designed with 8bits. If high efficiency is desired, the supply voltage should be kept at 5V. As of now, there are 8input lines. It consumes 8μA current.
74HCT377PW-Q100J Features
Tape & Reel (TR) package
74HCT series
20 pins
8 Bits
74HCT377PW-Q100J Applications
There are a lot of Nexperia USA Inc. 74HCT377PW-Q100J Flip Flops applications.
- Communications
- Test & Measurement
- Cold spare funcion
- Safety Clamp
- Count Modes
- Memory
- Clock pulse
- Bus hold
- Consumer
- Buffered Clock
