74HCT377PW,112
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 20 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tube |
| Published | 2013 |
| Series | 74HCT |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Type | D-Type |
| Additional Feature | WITH HOLD MODE |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Base Part Number | 74HCT377 |
| Function | Standard |
| Output Type | Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Number of Circuits | 8 |
| Number of Bits | 8 |
| Clock Frequency | 53MHz |
| Propagation Delay | 14 ns |
| Quiescent Current | 8μA |
| Turn On Delay Time | 17 ns |
| Family | HCT |
| Logic Function | D-Type, Flip-Flop |
| Current - Output High, Low | 4mA 5.2mA |
| Max Propagation Delay @ V, Max CL | 32ns @ 4.5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 3.5pF |
| Number of Input Lines | 10 |
| Clock Edge Trigger Type | Positive Edge |
| Length | 6.5mm |
| Width | 4.4mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
74HCT377PW,112 Overview
It is packaged in the way of 20-TSSOP (0.173, 4.40mm Width). The Tubepackage contains it. As configured, the output uses Non-Inverted. The trigger configured with it uses Positive Edge. There is an electrical part that is mounted in the way of Surface Mount. It operates with a supply voltage of 4.5V~5.5V. A temperature of -40°C~125°C TAis considered to be the operating temperature. The type of this D latch is D-Type. It is a type of FPGA belonging to the 74HCT series. Its output frequency should not exceed 53MHz Hz. There are 1 elements in it. There are 20 terminations,The 74HCT377 family contains it. Power is supplied from a voltage of 5V volts. A 3.5pFfarad input capacitance is provided by this T flip flop. It is a member of the HCTfamily of D flip flop. It is mounted by the way of Surface Mount. A total of 20pins are provided on this board. In this device, the clock edge trigger type is Positive Edge. An electronic part designed with 8bits is used in this application. Its superior flexibility is attributed to its use of 8 circuits. It is recommended that the supply voltage be kept at 5Vto maximize efficiency. This input has 10lines in it. There is 8μA quiescent current consumption by it. It is also characterized by WITH HOLD MODE.
74HCT377PW,112 Features
Tube package
74HCT series
20 pins
8 Bits
74HCT377PW,112 Applications
There are a lot of Nexperia USA Inc. 74HCT377PW,112 Flip Flops applications.
- ESCC
- Consumer
- Computing
- Synchronous counter
- Balanced 24 mA output drivers
- Test & Measurement
- Single Up Count-Control Line
- Parallel data storage
- Count Modes
- Memory
