74HCT4016D,112
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tube |
| Published | 1997 |
| JESD-609 Code | e4 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| Terminal Finish | NICKEL PALLADIUM GOLD |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 4.5V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | 74HCT4016 |
| Output | SEPARATE OUTPUT |
| Pin Count | 14 |
| JESD-30 Code | R-PDSO-G14 |
| Qualification Status | Not Qualified |
| Supply Voltage-Max (Vsup) | 5.5V |
| Power Supplies | 5V |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| -3db Bandwidth | 200MHz |
| On-State Resistance (Max) | 95Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 50 dB |
| Current - Leakage (IS(off)) (Max) | 1μA |
| Channel Capacitance (CS(off), CD(off)) | 3.5pF |
| On-state Resistance Match-Nom | 16Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 30ns, 44ns |
| Channel-to-Channel Matching (ΔRon) | 5 Ω |
| Crosstalk | -60dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 35ns |
| Switch-off Time-Max | 35ns |
| Voltage - Supply, Single (V+) | 4.5V~5.5V |
| Normal Position | NO |
| Height Seated (Max) | 1.75mm |
| Length | 8.65mm |
| RoHS Status | ROHS3 Compliant |
74HCT4016D,112 Overview
Packed in 14-SOIC (0.154, 3.90mm Width), the electronic component is convenient for shipping overseas. Advanced packaging method Tube is used to provide high reliability. The multiplexer is located in Surface Mount. The ratio between the number of multiplexer and demultiplexer circuits is 1:1. Operating temperature around -40°C~125°C TA extended. In total, there have been 14 terminations. The electronic part delivers high-quality output through its 1 channels. An 4.5V voltage supply should allow the electrical part to be turned on and run. As part of its design, the 14 series is equipped with this electronic component. These analog multiplexers are built based on SPST - NO switching circuits. It consists of 2 circuits. Try searching for the analog switch ic with 74HCT4016 if you are looking for variants. The analog multiplexer shown here is a typical Multiplexer or Switches. Using only a single voltage supply, this analog switch requires 4.5V~5.5V voltage. The outputs of this digital multiplexer are SEPARATE OUTPUT in number.
74HCT4016D,112 Features
1 Channels
Switch Circuit: SPST - NO
-3db Bandwidth: 200MHz
74HCT4016D,112 Applications
There are a lot of NXP USA Inc. 74HCT4016D,112 Analog Switches & Multiplexers ICs applications.
- Automotive applications
- Avionics and Military Systems
- Audio and video switching
- Video signal routing
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Avionics
- ISDN NT1/TA
- E1 Network Equipment
- Precision instrumentation
- Channelized and Unchannelized DS3 applications
