74HCT4052PW-Q100,1

60ns, 48ns SP4T 150Ohm Analog Switches BREAK-BEFORE-MAKE 74HCT4052 16 Pins 2μA 5V 16-TSSOP (0.173, 4.40mm Width)

Manufacturer: Nexperia USA Inc.
Nocochips NO: 554-74HCT4052PW-Q100,1
Package: 16-TSSOP (0.173, 4.40mm Width)
Datasheet: PDF
Stock: 547
Description: 60ns, 48ns SP4T 150Ohm Analog Switches BREAK-BEFORE-MAKE 74HCT4052 16 Pins 2μA 5V 16-TSSOP (0.173, 4.40mm Width)(Kg)

Details

Tags

Parameters
Factory Lead Time	1 Week
Mount	Surface Mount
Mounting Type	Surface Mount
Package / Case	16-TSSOP (0.173, 4.40mm Width)
Number of Pins	16
Weight	172.98879mg
Operating Temperature	-40°C~125°C TA
Packaging	Tape & Reel (TR)
Published	2010
Series	Automotive, AEC-Q100
JESD-609 Code	e4
Part Status	Active
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	16
Resistance	210Ohm
Terminal Finish	Nickel/Palladium/Gold (Ni/Pd/Au)
Max Power Dissipation	500mW
Technology	CMOS
Terminal Form	GULL WING
Number of Functions	2
Supply Voltage	5V
Terminal Pitch	0.65mm
Base Part Number	74HCT4052
Output	COMMON OUTPUT
Pin Count	16
Operating Supply Voltage	5V
Number of Channels	8
Number of Circuits	2
Max Supply Voltage	5.5V
Min Supply Voltage	4.5V
Analog IC - Other Type	SINGLE-ENDED MULTIPLEXER
Operating Supply Current	320μA
Power Dissipation	500mW
Propagation Delay	18 ns
Turn On Delay Time	105 ns
Logic Function	Demultiplexer, Multiplexer
Voltage - Supply, Single/Dual (±)	4.5V~5.5V ±1V~5V
Supply Type	Dual, Single
Bandwidth	180MHz
Turn-Off Delay Time	75 ns
Max Dual Supply Voltage	5V
On-State Resistance (Max)	150Ohm
Min Dual Supply Voltage	1V
Dual Supply Voltage	2.5V
Multiplexer/Demultiplexer Circuit	4:1
Off-state Isolation-Nom	50 dB
Current - Leakage (IS(off)) (Max)	2μA
Channel Capacitance (CS(off), CD(off))	3.5pF
Switch Circuit	SP4T
Switch Time (Ton, Toff) (Max)	60ns, 48ns
Channel-to-Channel Matching (ΔRon)	6 Ω
Crosstalk	-60dB @ 1MHz
Switching	BREAK-BEFORE-MAKE
Normal Position	NO
Height Seated (Max)	1.1mm
Length	5mm
Radiation Hardening	No
RoHS Status	ROHS3 Compliant

74HCT4052PW-Q100,1 Overview

The electronic part can be shipped overseas conveniently because it is packaged in 16-TSSOP (0.173, 4.40mm Width). High reliability is provided by advanced packaging method Tape & Reel (TR). This analog switch is mounted in Surface Mount. Multiplexers and demultiplexers have a ratio of 4:1. Operating temperature around -40°C~125°C TA extended. There are 16 terminations totally. A 8 channel electronic part produces high-quality output. If the voltage supply is 5V volts, the electrical component should be turned on and run. It is injected into the electrical part body with 16 pins. SP4T switching circuits are used in these analog switch ics. The multiplexer consists of 2 circuits. Try searching for the analog switch ic with 74HCT4052 if you are looking for variants. As far as internal resistance is concerned, it has 210Ohm. To find out what the functions of 16 pins are, please refer to their datasheets. Multiplexers should not be powered above 5.5V in normal situations. Analog switch ics with Dual, Single supply type are cost-effective. There should be 4.5V voltage fed to the electrical part below 4.5V. An operating current of 320μA would be sufficient for this switch device. For this multiplexer, dual supply voltage is feasible, but it should not exceed 5V. A dual power supply should have at least 1V voltage attached. An analog IC with the number SINGLE-ENDED MULTIPLEXER is integrated into this board. A total of COMMON OUTPUT outputs are available on this analog switch ic. It can operate from 5V operating voltages. The data can be transferred over a wide range of bandwidths, called 180MHz bandwidths. From the Automotive, AEC-Q100 series.