Parameters |
Factory Lead Time |
1 Week |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
16-TSSOP (0.173, 4.40mm Width) |
Number of Pins |
16 |
Operating Temperature |
-40°C~125°C TA |
Packaging |
Tape & Reel (TR) |
Published |
2013 |
JESD-609 Code |
e4 |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
Resistance |
210Ohm |
Terminal Finish |
Nickel/Palladium/Gold (Ni/Pd/Au) |
Max Power Dissipation |
500mW |
Technology |
CMOS |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
1 |
Supply Voltage |
4.5V |
Terminal Pitch |
0.65mm |
Time@Peak Reflow Temperature-Max (s) |
30 |
Base Part Number |
74HCT4052 |
Pin Count |
16 |
Operating Supply Voltage |
5V |
Number of Channels |
8 |
Number of Circuits |
2 |
Max Supply Voltage |
5.5V |
Min Supply Voltage |
4.5V |
Analog IC - Other Type |
DIFFERENTIAL MULTIPLEXER |
Operating Supply Current |
320μA |
Power Dissipation |
500mW |
Propagation Delay |
18 ns |
Turn On Delay Time |
105 ns |
Logic Function |
Demultiplexer, Demux, Multiplexer, Mux |
Voltage - Supply, Single/Dual (±) |
4.5V~5.5V ±1V~5V |
Supply Type |
Dual, Single |
Bandwidth |
180MHz |
Turn-Off Delay Time |
75 ns |
Max Dual Supply Voltage |
5V |
On-State Resistance (Max) |
150Ohm |
Min Dual Supply Voltage |
1V |
Dual Supply Voltage |
2.5V |
Multiplexer/Demultiplexer Circuit |
4:1 |
Off-state Isolation-Nom |
50 dB |
Current - Leakage (IS(off)) (Max) |
2μA |
Channel Capacitance (CS(off), CD(off)) |
3.5pF |
On-state Resistance Match-Nom |
9Ohm |
Switch Circuit |
SP4T |
Switch Time (Ton, Toff) (Max) |
60ns, 48ns |
Number of Output Lines |
10 |
Channel-to-Channel Matching (ΔRon) |
6 Ω |
Crosstalk |
-60dB @ 1MHz |
Switch-on Time-Max |
70ns |
Switch-off Time-Max |
50ns |
Height Seated (Max) |
1.1mm |
Length |
5mm |
Radiation Hardening |
No |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
74HCT4052PW,118 Overview
As the electronic part is packed in 16-TSSOP (0.173, 4.40mm Width), international shipping is convenient. This high-reliability packaging method uses advanced packaging methods Tape & Reel (TR). It is mounted in the position Surface Mount. 4:1 is the ratio of multiplexer to demultiplexer circuits. Temperatures around -40°C~125°C TA are extended for operation. In total, 16 terminations have occurred. High-quality output is provided by the electronic component's 8 channels. It is safe to turn on and run the electronic component with a 4.5V voltage supply. Into the electrical component body are injected 16 pins. The analog switch ics are built using SP4T switching circuits. This multiplexer is composed of 2 circuits. Try searching with 74HCT4052 if you're looking for variants. A 210Ohm internal resistance characterizes this multiplexer. Datasheets for functions of 16 pins are available. normally, users should not supply switches with voltages higher than 5.5V. A cost-effective Dual, Single supply type analogue multiplexer. 4.5V is the lowest voltage the electrical component should receive. In order to operate this switch device, it would need a current of 320μA. It is possible to supply this switch device with dual voltages. However, it is not advisable to exceed 5V. With dual power supplies, you should attach at least 1V. An analog IC with the number DIFFERENTIAL MULTIPLEXER is integrated into this board. There is a voltage range of 5V operating voltages for the electrical part. There are 180MHz bandwidths for data transfer.
74HCT4052PW,118 Features
8 Channels
Switch Circuit: SP4T
320μA Supply Current
Bandwidth: 180MHz
74HCT4052PW,118 Applications
There are a lot of Nexperia USA Inc. 74HCT4052PW,118 Analog Switches & Multiplexers ICs applications.
- Audio/video switches
- Isolation
- FTTH
- Voice over IP/DSL – Integrated Access Devices, Smart
- SONET
- Access Concentrators
- SDH/SONET multiplexers
- Multi-Line E1 Interface Cards
- Mechanical reed relay replacement
- Routers