74HCT4066D-Q100,11
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 14 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2011 |
| Series | Automotive, AEC-Q100 |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| Resistance | 35Ohm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 1.27mm |
| Base Part Number | 74HCT4066 |
| Pin Count | 14 |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Analog IC - Other Type | DIFFERENTIAL MULTIPLEXER |
| Operating Supply Current | 40μA |
| Throw Configuration | SPST |
| Supply Type | Single |
| -3db Bandwidth | 200MHz |
| On-State Resistance (Max) | 20Ohm Typ |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 50 dB |
| Current - Leakage (IS(off)) (Max) | 1μA |
| Channel Capacitance (CS(off), CD(off)) | 3.5pF |
| On-state Resistance Match-Nom | 5Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 44ns, 30ns |
| Channel-to-Channel Matching (ΔRon) | 3 Ω |
| Crosstalk | -60dB @ 1MHz |
| Switch-on Time-Max | 36ns |
| Switch-off Time-Max | 53ns |
| Voltage - Supply, Single (V+) | 4.5V~5.5V |
| Height Seated (Max) | 1.75mm |
| Length | 8.65mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
74HCT4066D-Q100,11 Overview
Shipping overseas is convenient due to the electrical component's packing in 14-SOIC (0.154, 3.90mm Width). Advanced packaging method Tape & Reel (TR) is used to provide high reliability. In Surface Mount, this analog switch is mounted. Multiplexers and demultiplexers have a ratio of 1:1. The operating temperature is extended to around -40°C~125°C TA. In total, 14 terminations have occurred. A electrical component with 1 channels is capable of high-quality output. An 5V voltage supply should allow the electrical part to be turned on and run. There is an electrical component included in the 14 series. A SPST - NO switching circuit is used for these analog switches. Circuits number 4 make up this analogue multiplexer. If you are looking for variants of the digital switch, trying search with 74HCT4066. This digital multiplexer has 35Ohm internal resistance. Datasheets for functions of 14 pins are available. In a normalsituation, users should not supply the switches with voltage higher than 5.5V. Single supply type digital switch with a low cost. 4.5V should be the lowest voltage fed to the electronic component. In order to operate this switch device, it would need a current of 40μA. Analogue multiplexers require a 4.5V~5.5V voltage to drain from a single voltage supply. An analog IC with the number DIFFERENTIAL MULTIPLEXER is integrated into this board. This is electronic component of the Automotive, AEC-Q100 series.
74HCT4066D-Q100,11 Features
1 Channels
Switch Circuit: SPST - NO
40μA Supply Current
-3db Bandwidth: 200MHz
74HCT4066D-Q100,11 Applications
There are a lot of Nexperia USA Inc. 74HCT4066D-Q100,11 Analog Switches & Multiplexers ICs applications.
- Voice over IP/DSL – Integrated Access Devices, Smart
- Communication systems
- Fiber to the Home
- Switching Systems
- Residential Gateways, Home Gateway/Router
- Fault Tolerant Systems
- HDTV
- T1/E1 Terminals
- Battery Powered Systems
- New designs requiring multiplexer functions
