Parameters |
Factory Lead Time |
1 Week |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
16-TSSOP (0.173, 4.40mm Width) |
Number of Pins |
16 |
Operating Temperature |
-40°C~125°C TA |
Packaging |
Tape & Reel (TR) |
Published |
2008 |
JESD-609 Code |
e4 |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
Resistance |
210Ohm |
Terminal Finish |
Nickel/Palladium/Gold (Ni/Pd/Au) |
Technology |
CMOS |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Number of Functions |
1 |
Supply Voltage |
5V |
Terminal Pitch |
0.65mm |
Base Part Number |
74HCT4852 |
Pin Count |
16 |
Number of Channels |
4 |
Number of Circuits |
2 |
Max Supply Voltage |
5.5V |
Min Supply Voltage |
4.5V |
Analog IC - Other Type |
DIFFERENTIAL MULTIPLEXER |
Operating Supply Current |
2μA |
Power Dissipation |
500mW |
Propagation Delay |
35 ns |
Logic Function |
Demultiplexer, Multiplexer |
Supply Type |
Single |
On-State Resistance (Max) |
210Ohm |
Multiplexer/Demultiplexer Circuit |
4:1 |
Number of Input Lines |
10 |
Current - Leakage (IS(off)) (Max) |
100nA |
Channel Capacitance (CS(off), CD(off)) |
10pF |
On-state Resistance Match-Nom |
2Ohm |
Switch Circuit |
SP4T |
Switch Time (Ton, Toff) (Max) |
25ns, 80ns |
Number of Output Lines |
8 |
Channel-to-Channel Matching (ΔRon) |
2 Ω |
Voltage - Supply, Single (V+) |
4.5V~5.5V |
Height Seated (Max) |
1.1mm |
Length |
5mm |
Width |
4.4mm |
Radiation Hardening |
No |
RoHS Status |
ROHS3 Compliant |
74HCT4852PW,118 Overview
This electronic part is conveniently packaged in 16-TSSOP (0.173, 4.40mm Width), making it easy to ship abroad. This high-reliability packaging method uses advanced packaging methods Tape & Reel (TR). The multiplexer is located in Surface Mount. Multiplexers and demultiplexers have the same number of circuits 4:1. The operating temperature is extended to around -40°C~125°C TA. Total terminations are 16. The electronic part provides high-quality output because it has 4 channels. An 5V voltage supply should allow the electrical part to be turned on and run. As part of the design of the 16 series, this electronic part has been incorporated into the system. On the other hand, analog switches can be constructed using SP4T switching circuits. A total of 2 circuits make up this switch device. Try searching for 74HCT4852 variants of the analog switch ic. A 210Ohm internal resistance characterizes this multiplexer. Please refer to the datasheets for 16 pins functions. Users should never supply a voltage higher than 5.5V to a switch device. The digital multiplexer has a low cost Single supply. It is recommended to use 4.5V as the lowest voltage for the electrical part. In order to operate this switch device, it would need a current of 2μA. This analog switch requires a voltage of 4.5V~5.5V to drain from a single voltage supply. A DIFFERENTIAL MULTIPLEXER analog IC is integrated into the board.
74HCT4852PW,118 Features
4 Channels
Switch Circuit: SP4T
2μA Supply Current
74HCT4852PW,118 Applications
There are a lot of Nexperia USA Inc. 74HCT4852PW,118 Analog Switches & Multiplexers ICs applications.
- Medical Instrumentation
- Audio and video switching
- T1/E1 Terminals
- USB 1.1 signal switching circuits
- Residential Gateways, Home Gateway/Router
- Cell phones
- Audio and video routing
- Modems
- Data switching
- New designs requiring multiplexer functions