74HCT74DB,118
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-SSOP (0.209, 5.30mm Width) |
| Number of Pins | 14 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2008 |
| Series | 74HCT |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| Type | D-Type |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | 74HCT74 |
| Function | Set(Preset) and Reset |
| Output Type | Differential |
| Operating Supply Voltage | 5V |
| Polarity | Non-Inverting |
| Number of Circuits | 2 |
| Clock Frequency | 59MHz |
| Propagation Delay | 60 ns |
| Quiescent Current | 80μA |
| Turn On Delay Time | 18 ns |
| Family | HCT |
| Logic Function | AND, D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 40μA |
| Current - Output High, Low | 4mA 4mA |
| Number of Bits per Element | 1 |
| Max Propagation Delay @ V, Max CL | 44ns @ 4.5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 3.5pF |
| Number of Output Lines | 1 |
| Clock Edge Trigger Type | Positive Edge |
| Width | 5.3mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
74HCT74DB,118 Overview
It is embeded in 14-SSOP (0.209, 5.30mm Width) case. D flip flop is embedded in the Tape & Reel (TR) package. In the configuration, Differentialis used as the output. It is configured with the trigger Positive Edge. Surface Mountmounts this electrical part. A supply voltage of 4.5V~5.5V is required for operation. Temperature is set to -40°C~125°C TA. This electronic flip flop is of type D-Type. It is a type of FPGA belonging to the 74HCT series. It should not exceed 59MHzin its output frequency. It consumes 40μA of quiescent current without being affected by external factors. In 14terminations, a transmission line is terminated with a JK flip flop that matches its characteristic impedance. The 74HCT74family includes it. The D flip flop is powered by a voltage of 5V . Its input capacitance is 3.5pFfarads. In this case, the D flip flop belongs to the HCTfamily. There is an electronic component mounted in the way of Surface Mount. With its 14pins, it is designed to work with most electronic flip flops. There is a clock edge trigger type of Positive Edgeon this device. The superior flexibility is achieved through the use of 2 circuits. If high efficiency is to be achieved, the supply voltage should be maintained at 5V. There are 1 output lines in this JK flip flop. In terms of quiescent current, it consumes 80μA .
74HCT74DB,118 Features
Tape & Reel (TR) package
74HCT series
14 pins
74HCT74DB,118 Applications
There are a lot of Nexperia USA Inc. 74HCT74DB,118 Flip Flops applications.
- 2 – Bit synchronous counter
- Instrumentation
- Frequency division
- Power down protection
- Storage Registers
- Balanced Propagation Delays
- Control circuits
- Registers
- Reduced system switching noise
- Data storage
