74LCX374MTCX
| Parameters | |
|---|---|
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 20 |
| Weight | 191mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2009 |
| Series | 74LCX |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Voltage - Supply | 2V~3.6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Supply Voltage | 2.5V |
| Terminal Pitch | 0.65mm |
| Base Part Number | 74LCX374 |
| Function | Standard |
| Output Type | Tri-State, Non-Inverted |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Number of Bits | 8 |
| Clock Frequency | 150MHz |
| Propagation Delay | 10.5 ns |
| Quiescent Current | 10μA |
| Turn On Delay Time | 8.5 ns |
| Family | LVC/LCX/Z |
| Logic Function | D-Type, Flip-Flop |
| Current - Output High, Low | 24mA 24mA |
| Max I(ol) | 0.024 A |
| Max Propagation Delay @ V, Max CL | 8.5ns @ 3.3V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 7pF |
| Number of Output Lines | 3 |
| Clock Edge Trigger Type | Positive Edge |
| Length | 6.5mm |
| Width | 4.4mm |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
74LCX374MTCX Overview
The flip flop is packaged in 20-TSSOP (0.173, 4.40mm Width). It is contained within the Tape & Reel (TR)package. Tri-State, Non-Invertedis the output configured for it. It is configured with the trigger Positive Edge. There is an electrical part that is mounted in the way of Surface Mount. The JK flip flop operates with an input voltage of 2V~3.6V volts. Temperature is set to -40°C~85°C TA. Logic flip flops of this type are classified as D-Type. JK flip flop is a part of the 74LCXseries of FPGAs. Its output frequency should not exceed 150MHz Hz. A total of 1elements are present in it. There have been 20 terminations. The 74LCX374 family contains it. The D flip flop is powered by a voltage of 2.5V . This JK flip flop has a 7pFfarad input capacitance. Electronic devices of this type belong to the LVC/LCX/Zfamily. There is an electronic part mounted in the way of Surface Mount. A total of 20pins are provided on this board. A Positive Edgeclock edge trigger is used in this device. The part is included in FF/Latches. The design is based on 8bits. If you want to maintain normal operation, you should keep the supply voltage (Vsup) above 2V. Its flexibility is enhanced by 8 circuits. A reliable performance of this D flip flop makes it well suited for use in TAPE AND REEL. A D flip flop with 2embedded ports is available. The JK flip flop is with 3 output lines to operate. Despite external influences, it consumes 10μAof quiescent current.
74LCX374MTCX Features
Tape & Reel (TR) package
74LCX series
20 pins
8 Bits
74LCX374MTCX Applications
There are a lot of ON Semiconductor 74LCX374MTCX Flip Flops applications.
- Single Down Count-Control Line
- Common Clocks
- Reduced system switching noise
- Cold spare funcion
- Supports Live Insertion
- Safety Clamp
- Digital electronics systems
- Shift Registers
- Balanced 24 mA output drivers
- Divide a clock signal by 2 or 4
