74LCX74MTCX
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 14 |
| Weight | 55.3mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2016 |
| Series | 74LCX |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Voltage - Supply | 2V~3.6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 2.5V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | 74LCX74 |
| Function | Set(Preset) and Reset |
| Number of Outputs | 4 |
| Output Type | Differential |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 3.6V |
| Power Supplies | 3.3V |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Channels | 2 |
| Load Capacitance | 50pF |
| Clock Frequency | 150MHz |
| Propagation Delay | 8 ns |
| Quiescent Current | 10μA |
| Turn On Delay Time | 7 ns |
| Family | LVC/LCX/Z |
| Logic Function | AND, D-Type, Flip-Flop |
| Current - Output High, Low | 24mA 24mA |
| Number of Bits per Element | 1 |
| Max Propagation Delay @ V, Max CL | 7ns @ 3.3V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 7pF |
| Clock Edge Trigger Type | Positive Edge |
| Height | 900μm |
| Length | 5mm |
| Width | 4.4mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
74LCX74MTCX Overview
The flip flop is packaged in a case of 14-TSSOP (0.173, 4.40mm Width). As part of the package Tape & Reel (TR), it is embedded. T flip flop uses Differentialas the output. JK flip flop uses Positive Edgeas the trigger. Surface Mountis positioned in the way of this electronic part. The JK flip flop operates at 2V~3.6Vvolts. A temperature of -40°C~85°C TAis used in the operation. Logic flip flops of this type are classified as D-Type. In terms of FPGAs, it belongs to the 74LCX series. It should not exceed 150MHzin its output frequency. 14terminations have occurred. You can search similar parts based on 74LCX74. A voltage of 2.5V is used to power it. The input capacitance of this T flip flop is 7pF farads, which is defined as the capacitance between the input terminals of an op amp with either input grounded. Electronic devices of this type belong to the LVC/LCX/Zfamily. It is mounted by the way of Surface Mount. The 14pins are designed into the board. It has a clock edge trigger type of Positive Edge. It is part of the FF/Latchesbase part number family. Vsup reaches 3.6V, the maximal supply voltage. For normal operation, the supply voltage (Vsup) should be kept above 2V. This D flip flop is well suited for TAPE AND REEL based on its reliable performance. In order for the device to operate, it requires 3.3V power supplies. There is 10μA quiescent current consumption by it. A total of 2 channels are available.
74LCX74MTCX Features
Tape & Reel (TR) package
74LCX series
14 pins
3.3V power supplies
74LCX74MTCX Applications
There are a lot of ON Semiconductor 74LCX74MTCX Flip Flops applications.
- Synchronous counter
- Circuit Design
- Asynchronous counter
- Registers
- Pattern generators
- High Performance Logic for test systems
- Control circuits
- ESCC
- Computing
- Divide a clock signal by 2 or 4
