74LV4052D-Q100J
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Series | Automotive, AEC-Q100 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Resistance | 135Ohm |
| Max Power Dissipation | 500mW |
| Base Part Number | 74LV4052 |
| Pin Count | 16 |
| Operating Supply Voltage | 3.3V |
| Polarity | Non-Inverting |
| Number of Circuits | 2 |
| Max Supply Voltage | 6V |
| Min Supply Voltage | 1V |
| Operating Supply Current | 80μA |
| Propagation Delay | 9 ns |
| Logic Function | Demultiplexer, Multiplexer |
| Supply Type | Single |
| -3db Bandwidth | 200MHz |
| On-State Resistance (Max) | 85Ohm |
| High Level Output Current | 25mA |
| Multiplexer/Demultiplexer Circuit | 4:1 |
| Number of Input Lines | 8 |
| Current - Leakage (IS(off)) (Max) | 2μA |
| Channel Capacitance (CS(off), CD(off)) | 3.5pF |
| Switch Circuit | SP4T |
| Switch Time (Ton, Toff) (Max) | 46ns, 32ns |
| Channel-to-Channel Matching (ΔRon) | 2 Ω |
| Crosstalk | -60dB @ 1MHz |
| Voltage - Supply, Single (V+) | 1V~6V |
| RoHS Status | ROHS3 Compliant |
74LV4052D-Q100J Overview
As the electronic part is packed in 16-SOIC (0.154, 3.90mm Width), international shipping is convenient. This packaging method provides high reliability because it uses advanced packaging techniques. Mounted in Surface Mount is this multiplexer. 4:1 is the ratio of multiplexer to demultiplexer circuits. Operation at a temperature around -40°C~125°C TA. The electrical component body receives 16 pins. A SP4T switching circuit is used for these analog switches. A total of 2 circuits make up this switch device. Try searching for 74LV4052 variants of the analog switch ic. As far as internal resistance is concerned, it has 135Ohm. Please refer to the datasheets for 16 pins functions. Users should never supply a voltage higher than 6V to a switch device. The digital multiplexer has a low cost Single supply. The lowest voltage the electronic part should receive is 1V. The analogue multiplexer could operate on 80μA current. The voltage required by this switch device is 1V~6V, draining from a single voltage supply. This electrical part is compatible with 3.3V operating voltages. The Automotive, AEC-Q100 series is responsible for it.
74LV4052D-Q100J Features
Switch Circuit: SP4T
80μA Supply Current
-3db Bandwidth: 200MHz
74LV4052D-Q100J Applications
There are a lot of Nexperia USA Inc. 74LV4052D-Q100J Analog Switches & Multiplexers ICs applications.
- Audio/video switches
- Microprocessor controlled systems
- Communications systems
- Fiber to the Home
- Frame Relay Equipment
- Communication systems
- E1 Multiplexer
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- DVD-R
- Cable Modem
