74LV4052DB,112
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SSOP (0.209, 5.30mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tube |
| Published | 2013 |
| JESD-609 Code | e4 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 135Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 400mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 6V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | 74LV4052 |
| Pin Count | 16 |
| Operating Supply Voltage | 3.3V |
| Polarity | Non-Inverting |
| Number of Channels | 8 |
| Number of Circuits | 2 |
| Max Supply Voltage | 6V |
| Min Supply Voltage | 1V |
| Analog IC - Other Type | DIFFERENTIAL MULTIPLEXER |
| Operating Supply Current | 80μA |
| Power Dissipation | 400mW |
| Propagation Delay | 8 ns |
| Turn On Delay Time | 190 ns |
| Logic Function | Demultiplexer, Multiplexer |
| Supply Type | Dual, Single |
| Bandwidth | 200MHz |
| Turn-Off Delay Time | 125 ns |
| On-State Resistance (Max) | 85Ohm |
| High Level Output Current | 25mA |
| Multiplexer/Demultiplexer Circuit | 4:1 |
| Off-state Isolation-Nom | 50 dB |
| Current - Leakage (IS(off)) (Max) | 2μA |
| Channel Capacitance (CS(off), CD(off)) | 3.5pF |
| On-state Resistance Match-Nom | 2Ohm |
| Switch Circuit | SP4T |
| Switch Time (Ton, Toff) (Max) | 46ns, 32ns |
| Channel-to-Channel Matching (ΔRon) | 2 Ω |
| Crosstalk | -60dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 56ns |
| Voltage - Supply, Single (V+) | 1V~6V |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
74LV4052DB,112 Overview
Shipping overseas is convenient with the electronic component packed in 16-SSOP (0.209, 5.30mm Width). To ensure high reliability, a new packaging method Tube is used. The multiplexer is located in Surface Mount. 4:1 is the ratio of multiplexer to demultiplexer circuits. Operation at a temperature around -40°C~125°C TA. There are 16 terminations totally. The electronic part delivers high-quality output through its 8 channels. An 6V voltage supply should allow the electrical part to be turned on and run. As part of the design of the 16 series, this electronic part has been incorporated into the system. Unlike digital switches, these are based on SP4T switching circuits. There are 2 circuits in this multiplexer. Try searching with 74LV4052 to find analog multiplexer variants. There is 135Ohm internal resistance in this digital multiplexer. You can find the functions of the 16 pins in the datasheets. The analogue multiplexer in this example is a typical Multiplexer or Switches. A voltage higher than 6V should not normally be supplied to the switches. Dual, Single supply type digital switch with a low cost. 1V should be the lowest voltage fed to the electronic component. An operating current of 80μA would be sufficient for this switch device. Draining from a single voltage supply, this analog switch requires a voltage of 1V~6V. There is an integrated analog IC DIFFERENTIAL MULTIPLEXER in the module. It can operate from 3.3V operating voltages. The transfer of data can be performed over 200MHz bandwidths.
74LV4052DB,112 Features
8 Channels
Switch Circuit: SP4T
80μA Supply Current
Bandwidth: 200MHz
74LV4052DB,112 Applications
There are a lot of Nexperia USA Inc. 74LV4052DB,112 Analog Switches & Multiplexers ICs applications.
- Video switching
- Automatic test equipment
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Audio and video signal routing
- Battery-powered systems
- Multi-Line E1 Interface Cards
- E1 Multiplexer
- Battery Powered Systems
- High speed data transmission line cards
- SDH
