Parameters |
Switch-on Time-Max |
30ns |
Voltage - Supply, Single (V+) |
1V~6V |
Height Seated (Max) |
1.75mm |
Length |
8.65mm |
Radiation Hardening |
No |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
Factory Lead Time |
1 Week |
Contact Plating |
Gold |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
14-SOIC (0.154, 3.90mm Width) |
Number of Pins |
14 |
Operating Temperature |
-40°C~125°C TA |
Packaging |
Tape & Reel (TR) |
Published |
2001 |
JESD-609 Code |
e4 |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
14 |
Resistance |
40Ohm |
Max Power Dissipation |
500mW |
Technology |
CMOS |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
4 |
Supply Voltage |
3.3V |
Terminal Pitch |
1.27mm |
Time@Peak Reflow Temperature-Max (s) |
30 |
Base Part Number |
74LV4066 |
Pin Count |
14 |
Operating Supply Voltage |
3.3V |
Polarity |
Non-Inverting |
Number of Channels |
1 |
Max Supply Voltage |
6V |
Min Supply Voltage |
1V |
Operating Supply Current |
80μA |
Power Dissipation |
500mW |
Max Supply Current |
80μA |
Throw Configuration |
SPST |
Turn On Delay Time |
40 ns |
Number of Inputs |
4 |
Supply Type |
Single |
Turn-Off Delay Time |
50 ns |
-3db Bandwidth |
200MHz |
On-State Resistance (Max) |
35Ohm |
High Level Output Current |
25mA |
Low Level Output Current |
25mA |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
50 dB |
Current - Leakage (IS(off)) (Max) |
2μA |
Channel Capacitance (CS(off), CD(off)) |
3.5pF |
On-state Resistance Match-Nom |
2Ohm |
Switch Circuit |
SPST - NO |
Switch Time (Ton, Toff) (Max) |
16ns, 28ns |
Crosstalk |
-60dB @ 1MHz |
74LV4066D,118 Overview
The electronic component is convenient to ship overseas because it is packed in a 14-SOIC (0.154, 3.90mm Width). In order to provide high reliability, an advanced packaging method Tape & Reel (TR) is used. This analog switch is mounted in Surface Mount. Multiplexer and demultiplexer circuits have a number 1:1. Extended operating temperature around -40°C~125°C TA. A total of 14 terminations have been recorded. By its 1 channels, the electronic component provides high-quality output. With a 3.3V voltage supply, the electrical component should be turned on and run. A key feature of the 14 series is the inclusion of this electronic part as part of its design. Multiplexers built on a SPST - NO switching circuit are built. Try searching with 74LV4066 to find analog multiplexer variants. A 40Ohm internal resistance characterizes this multiplexer. Please refer to the datasheets for 14 pins functions. It is generally not recommended to supply a voltage higher than 6V to the switch device in normal circumstances. The digital multiplexer has a low cost Single supply. It is recommended that the electrical component receives a voltage of 1V. 80μA current would be enough for this multiplexer to operate. A voltage of 1V~6V is required for this switch device, which drains from a single voltage source. If you put voltage higher than 80μA on the digital multiplexer, damage may occur. 3.3V operating voltages are supported by the electronic component. In order to operate the 4 inputs, there are several steps to follow.
74LV4066D,118 Features
1 Channels
Switch Circuit: SPST - NO
80μA Supply Current
-3db Bandwidth: 200MHz
74LV4066D,118 Applications
There are a lot of Nexperia USA Inc. 74LV4066D,118 Analog Switches & Multiplexers ICs applications.
- Precision instrumentation
- Sample hold systems
- Digital Cross-Connects
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- High speed data transmission line cards
- PCMCIA cards
- Routers
- Fiber In The Loop (FITL)
- SONET
- E1 Multiplexer