74LV4066PW,112
| Parameters | |
|---|---|
| Length | 5mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 14 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tube |
| Published | 2007 |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| Resistance | 40Ohm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Max Power Dissipation | 400mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 3.3V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | 74LV4066 |
| Pin Count | 14 |
| Operating Supply Voltage | 3.3V |
| Number of Channels | 1 |
| Max Supply Voltage | 6V |
| Min Supply Voltage | 1V |
| Operating Supply Current | 80μA |
| Power Dissipation | 400mW |
| Max Supply Current | 80μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 40 ns |
| Number of Inputs | 4 |
| Supply Type | Single |
| Turn-Off Delay Time | 50 ns |
| -3db Bandwidth | 200MHz |
| On-State Resistance (Max) | 35Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 50 dB |
| Current - Leakage (IS(off)) (Max) | 2μA |
| Channel Capacitance (CS(off), CD(off)) | 3.5pF |
| On-state Resistance Match-Nom | 2Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 16ns, 28ns |
| Crosstalk | -60dB @ 1MHz |
| Switch-on Time-Max | 30ns |
| Voltage - Supply, Single (V+) | 1V~6V |
| Height Seated (Max) | 1.1mm |
74LV4066PW,112 Overview
Shipping overseas is convenient due to the electrical component's packing in 14-TSSOP (0.173, 4.40mm Width). The advanced packaging method Tube provides high reliability. It is mounted in the position Surface Mount. Multiplexers and demultiplexers have the same number of circuits 1:1. Increasing operating temperature to around -40°C~125°C TA. In total, there have been 14 terminations. A high-quality output is provided by the electrical component's 1 channels. When the electronic component is given a voltage of 3.3V, it should be turned on and run. An electrical component like this is included in the 14 series. These analog multiplexers are built based on SPST - NO switching circuits. Search with 74LV4066 if you are looking for analog multiplexer variants. There is 40Ohm internal resistance in this digital multiplexer. Datasheets for functions of 14 pins are available. Users should never supply a voltage higher than 6V to a switch device. Single supply type digital switch with a low cost. It is recommended to use 1V as the lowest voltage for the electrical part. It would be sufficient to run this analogue multiplexer with 80μA current. Analogue multiplexers require a 1V~6V voltage to drain from a single voltage supply. A digital multiplexer may suffer damage if voltage is applied above 80μA. 3.3V operating voltages can be used with this electrical part. The 4 inputs need to be operated in order to work.
74LV4066PW,112 Features
1 Channels
Switch Circuit: SPST - NO
80μA Supply Current
-3db Bandwidth: 200MHz
74LV4066PW,112 Applications
There are a lot of Nexperia USA Inc. 74LV4066PW,112 Analog Switches & Multiplexers ICs applications.
- Isolation
- Access Concentrators
- Cellular phones
- Battery Powered Systems
- E1 Network Equipment
- Audio and video signal routing
- Digital cross connects (DSX-1)
- Central office
- Video signal routing
- Audio and video switching
